Closures DIN18
Fine Mist Sprayer, White, 18/415, 1000 pc
A plastic fine mist sprayer with an 18/415 neck finish turns an ordinary bottle into packaging that applies its contents as a fine, dispersed mist , without pouring and without your hands touching the contents. full description
Lowest price in the last 30 days: €250.00
Save €140.00 with this set
Product description
A plastic fine mist sprayer with an 18/415 neck finish turns an ordinary bottle into packaging that applies its contents as a fine, dispersed mist, without pouring and without your hands touching the contents. It is used for toners, facial mists, hydrolates, refreshing hair and body sprays, alcohol-based solutions and fragrance testers. The white closure with its head fits all of our bottles with an 18/415 neck. The dip tube has the length stated in the product name and can be shortened to match the height of the bottle.
The pack of 1 000 is intended for manufacturers and workshops that fill larger batches.
What it is suitable for
- Toners and hydrolates – low-viscosity water-based solutions disperse evenly and can be applied directly to the face without a cotton pad.
- Facial and body mists – light formulations with glycerine, hyaluronic acid or plant extracts that are left to dry on the skin.
- Alcohol-based solutions – eaux de toilette, eaux de parfum, hair tonics and refreshing sprays with an alcohol base.
- Hair sprays – detangling and smoothing sprays that are oil-free or contain a small proportion of oil in solubilised form.
- Testers and samples – small bottles with eau de parfum, hydrolate or a product sample for customers.
How the sprayer works
When the head is pressed, the piston draws the contents up through the dip tube and pushes them out through the nozzle as a dispersed mist. One press dispenses approximately 0.13 ml. This amount is enough for one application to the face or for dampening a cotton pad. For body sprays, expect several presses per area.
The first few presses after filling serve to prime the mechanism. Until the dip tube and piston fill with the contents, the sprayer dispenses nothing or dispenses unevenly. All pump closures behave this way; it is not a defect.
Shorten the dip tube with a sharp knife or scissors using an angled cut, so that it ends just above the bottom of the bottle. A tube that is too long bends, and the sprayer then draws the contents from the side. A tube that is too short leaves an unused residue at the bottom.
Use with a formulation
The sprayer is designed for water-based and alcohol-based solutions with low viscosity. The thicker the contents, the worse they disperse through the nozzle and the sooner it clogs. Mists with a thickener, serums with a higher proportion of gelling agents and emulsions with visible viscosity do not dispense well through this type of nozzle, even though the contents may pass through the piston. A pump with a larger dose is more suitable for such products.
Pure vegetable oils and oil serums usually leave the nozzle in a thin stream and do not disperse into a mist. We recommend testing the behaviour of your specific oil blend on a single piece before filling the whole batch.
The sprayer is made of polypropylene (PP). We have not verified its resistance with contents that have a higher proportion of essential oils or solvents, or with concentrated alcohol-based solutions. For such formulations, we recommend leaving the filled packaging to stand for several weeks and monitoring tightness, the colour of the contents and the function of the mechanism.
When choosing a bottle, leave headroom above the liquid level for the volume taken up by the dip tube and piston. A bottle filled to the neck will overflow when the sprayer is screwed on.
Good to know
Before first use, we recommend rinsing the sprayer with clean water or a solution of isopropyl alcohol and letting it dry.
The packaging is suitable for use with cosmetic products and meets the relevant legislative requirements. The technical documentation and declaration of conformity are available on the product page.
The sprayer can be reused. After emptying, rinse it with warm water, spray clean water through the nozzle several times and leave it to dry disassembled. Dried residues of the contents in the nozzle are the most common cause of uneven dispensing.
For recycling, the sprayer belongs with plastics. Unscrew the head from the bottle and sort the parts by material.
Closures with the same neck type and ready-made bottle + sprayer combinations can be found in the Handymade range. If you are making your own combination, we recommend checking the tightness of the thread, the dispensing and the behaviour of the packaging with your specific formulation.
Frequently asked questions
Parameters
Product documentation
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.

