PLASTIC BOTTLES
Clear Flat Plastic Bottle, White Cap, White Smooth Pump, 50 ml
The 50 ml plastic bottle with pump dispenses thinner cosmetic products in single doses of approximately 1 ml , without opening the bottle and without your fingers touching the contents. full description
Lowest price in the last 30 days: €0.93
Total for 1 pcs: €0.93
Quantities add up across all combinations of this bottle.
Product description
The 50 ml plastic bottle with pump dispenses thinner cosmetic products in single doses of approximately 1 ml, without opening the bottle and without your fingers touching the contents. This way, you take only as much product as you need. The flat clear PET bottle shows the colour and the remaining amount, and it fits into a handbag or a travel case. The set of bottle and white pump with 28/410 neck finish is declared suitable for contact with cosmetics.
Suitable uses
The pump dispenses liquid to medium-thick products. Thick creams and balms will not pass through it, so a jar or a tube is more suitable for them.
- Body and facial lotions – thinner emulsions where a measured dose per press is useful.
- Cleansing gels and liquid soaps – the measured amount is applied directly to the palm or a flannel.
- Moisturising gels and light fluids – including hand gels and products with lower viscosity.
- Samples and travel packs – the flat bottle takes up little space in luggage.
- Shampoos and conditioners for travel – if the product has a consistency that the pump can handle.
Filling and dispensing
The nominal volume of 50 ml is the amount the bottle is designed for in normal filling. The actual brimful volume is slightly larger. The difference provides room for the tube and the body of the pump, and for the expansion of the contents when the temperature changes. For this reason, fill to the nominal volume, not to the brim. If the bottle is overfilled, fitting the pump would push part of the contents out through the neck.
After screwing on the pump, press it several times without product until the tube fills and the product starts to flow out. With thicker products, the first priming takes longer.
If you are not sure whether your emulsion or gel will pass through the pump, fill a small amount first and test the dispensing. A product that comes out only with difficulty after pressing, or that clogs the pump, is better suited to a jar.
Good to know
Before the first filling, rinse the bottle and the pump, disinfect them with isopropyl alcohol or ethanol and leave them to dry completely. Moisture left in the tube or in the body of the pump would get into the product. The same procedure applies to repeated filling. First rinse the pump with clean water and then with alcohol, so that no residues of the previous product remain in it.
PET does not tolerate high temperatures. Do not sterilise the bottle with boiling water and do not fill it with a hot emulsion – let the contents cool down before filling. For products with a higher proportion of essential oils or solvents, check how the plastic behaves in the finished formulation.
The pump is not an airtight closure. Water-based and emulsion products filled into this bottle must be properly preserved, just as in any other open packaging. Before transporting the bottle in a bag, check that the pump does not activate when pressed accidentally, or carry it in a separate bag.
The certificate for direct contact with food applies to the bottle on its own. The pump does not have this declaration, so the set as a whole is intended for cosmetics. Closures with the same neck type as stated in the parameters, as well as other ready-made combinations, are available in the Handymade range. If you make your own combination with a different closure, check the seal and the dispensing with your specific formulation.
The bottle is made of PET, which is one of the commonly recycled plastics. Before disposal, empty the packaging and separate the pump.
Frequently asked questions
Parameters
Clear Flat Plastic Bottle, 50 ml
- Product colour
- Clear
- Country of origin
- European Union
- Nominal capacity
- 50
- Diameter
- 46,5 x 24,5 mm mm
- Thread type
- SPCO 1881
- Height
- 127 mm
Plastic pump, white, 28/410
Product documentation
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.

















