Ludivine D.29 Sept 2026
Scent: Plastová pumpička, biela, hadička 130 mm, 28/410
Very good quality
Translated automatically
Closures DIN28
Plastic pump, white, dip tube 130 mm, 28/410
Plastic pump, white, 28/410 This is a dispensing pump with a dip tube that turns an ordinary bottle into a convenient dispenser for liquid and gel preparations. full description
In stock · 850 ks
OVD28PB_130
€0.65incl. VAT
Lowest price in the last 30 days: €0.65
Product description
Plastic pump, white, 28/410
This is a dispensing pump with a dip tube that turns an ordinary bottle into a convenient dispenser for liquid and gel preparations. When the head is pressed, it draws the contents through the tube and delivers them in a measured dose, so you dispense the product cleanly, hygienically and without spilling. It works wherever you want to portion a product one serving at a time — body and facial lotions, liquid soaps, gels, lighter creams or oils.
The pump has a 28/410 thread that screws onto a bottle with the same neck finish. It is made of plastic, so it is lightweight and unbreakable, and a single press delivers approximately 1 ml of contents, making repeated dosing and consumption estimates straightforward.
Key features
- Measured dispensing – one press delivers approximately 1 ml, suitable for products applied in small portions.
- Dip tube – reaches the contents even at the bottom of the bottle, making it ideal for taller containers with the same neck finish.
- 28/410 thread – a standard neck finish found on a large proportion of the bottles in the Handymade range.
- Plastic – an unbreakable, lightweight closure suitable for everyday facial and body preparations.
Use in formulation
The pump is best suited to liquid to medium-viscosity contents that it can reliably draw through the tube — body and facial lotions, liquid and cream soaps, shampoos, shower gels, lighter emulsions, hydrophilic oils and tonics. With very thick creams or pastes the pump may struggle to prime, so with denser textures verify the flow with your specific formulation before filling an entire batch.
The material is suitable for contact with cosmetic preparations. For contents with a higher proportion of essential oils, solvents or alcohol, we recommend checking the long-term compatibility of the plastic parts with the formulation — certain ingredients may soften the plastic or affect the seal over time.
Before first use, press the pump several times without any contents — until the tube and mechanism have primed, the first strokes will deliver less or nothing. This is the normal "priming" of the pump, not a defect.
Good to know
Fill the bottle with adequate headspace at the neck — the tube and mechanism take up some of the volume and the contents need room to move when pressed. Trim the dip tube to match the height of the bottle; if the tube is longer than the base of the container, it can be cut to the required length.
Before first filling, wash and disinfect both the container and the pump (for example with isopropyl alcohol or ethanol) and allow them to dry thoroughly. When reusing, rinse the mechanism with lukewarm water so that no product residue remains in the tube that could clog the dispenser.
The pump only fits a bottle with the same neck finish (28/410). Ready-made bottle and pump combinations are available in the Handymade range; with your own combination we recommend verifying the seal and smooth dispensing with the specific contents.
Frequently asked questions
What type of bottle does the pump fit?
The pump screws onto a bottle with a 28/410 thread. This is a widely used neck finish, so it is compatible with a number of bottles in the range. With your own combination always check that the bottle neck matches this thread and that the pump seals properly.
How thick a product can the pump dispense?
It works best with liquid to medium-viscosity contents such as lotions, liquid soaps, shampoos and lighter emulsions. With very thick creams or pastes, priming through the tube may be limited, so test the flow in advance with denser textures.
Why does the pump not dispense anything on the first press?
This is normal — the tube and mechanism are empty at the start. A few presses without contents will prime the system and the pump will then dispense fully. This is not a defect but the standard priming of a dispenser.
Can the pump be used with oils and alcohol-based preparations?
Yes, it can be used with oil-based and alcohol-based contents, but compatibility should be verified with the specific formulation. A higher proportion of essential oils, solvents or alcohol may affect the plastic parts over time, so for such contents we recommend a seal and dispensing test.
How is the pump cleaned and can it be reused?
Yes, the pump is designed for repeated use. Before first and subsequent fillings, wash it, disinfect with alcohol and allow it to dry; rinse the mechanism with lukewarm water so that no product residue remains in the tube that could clog the dispenser.
Parameters
Product documentation
- PDSProduct Data Sheet
- PDF ↓