PLASTIC BOTTLES
White Plastic Bottle, HDPE, White Pump, 100 ml
Pack size100 ml500 ml
Bottle and pump set for liquid and semi-liquid cosmetic products , 100 ml . The pump measures out the same dose with every press, so the contents can be dispensed without opening the packaging and without fingers… full description
Lowest price in the last 30 days: €1.34
Save €0.01 with this set
Total for 1 pcs: €1.34
Quantities add up across all combinations of this bottle.
Product description
Bottle and pump set for liquid and semi-liquid cosmetic products, 100 ml. The pump measures out the same dose with every press, so the contents can be dispensed without opening the packaging and without fingers touching the product. Both the bottle and the pump are declared suitable for contact with cosmetics.
The opaque white wall dims the light, so the bottle also protects ingredients sensitive to sunlight, such as vegetable oils or vitamins in emulsions. HDPE is a lightweight plastic that does not break when dropped in the bathroom, can be squeezed and returns to its shape when released. The packaging is suitable for home production as well as for small batches intended for sale.
What the set is suitable for
The pump works best with products that flow but are not completely watery. Typical home-made formulations include:
- Body and face lotions – light O/W emulsions that the pump draws up without effort.
- Liquid soaps and shower gels – medium-thick rinse-off products for which dispensing with a single press has proved the most effective.
- Lower-viscosity serums – gel or emulsion serums that do not require airless packaging.
- Body oils and massage blends – HDPE tolerates common oils; with a high proportion of essential oils, check the behaviour of the plastic beforehand.
The pump will dispense very thin water-based solutions, such as toners or hydrosols, but they may drip from the nozzle. A fine mist sprayer with the same neck finish is often more suitable for them. The pump cannot draw up thick creams and butters, which are better suited to a jar.
How the pump dispenses
One full press releases approximately 1 ml of the contents. This figure makes it easier to dose more concentrated products and also helps when writing instructions for use for your customers. Before first use, press the pump several times until the tube fills and the first dose comes out in full.
The dip tube reaches to the bottom of the bottle so that the contents can be used almost without residue. If it rests against the bottom and bends after screwing on, shorten it with a sharp knife or scissors so that it ends just above the bottom.
Before filling the whole batch, pour a sample of the finished product into one bottle and try the pump. This lets you check that the viscosity is right, that the dose does not drip and that no bubbles form in the tube.
Nominal and total volume
The nominal volume is the amount the bottle is designed for during normal filling. The physical volume up to the neck is larger. The difference provides a reserve for the tube and the pump body, which take up part of the space after screwing on, and for the expansion of the contents with temperature changes. The bottle should therefore be filled to the nominal volume, not to the brim. If it is overfilled, the contents are pushed out through the neck when the pump is screwed on.
Good to know
Before first filling, wash the bottle and the pump, disinfect them with isopropyl alcohol or ethanol and leave them to dry completely. Residual water would dilute the product and could jeopardise its microbiological stability.
The packaging can be reused. When changing the contents, thoroughly clean the tube and the inside of the pump, where residues of the previous product linger the longest. HDPE tolerates common cosmetic raw materials, including oils, surfactants and alcohol. With concentrated essential oils, fragrance compositions and some solvents, the plastic may over time absorb the scent or soften, so test the packaging with your specific formulation.
The bottle is made of HDPE and the pump of PP. Both materials are recyclable. Before disposal, separate the pump from the bottle and rinse the bottle.
The set is not approved for contact with food. Use it for cosmetic products; for home-made oils or syrups, choose packaging with the relevant certificate.
Closures with the same 28/410 neck finish and other ready-made bottle and closure combinations can be found in the Handymade range. If you make your own combination, check the tightness and dispensing with your specific formulation.
Frequently asked questions
Parameters
Plastic bottle HDPE 28/410, white, 100 ml
- Product colour
- White
- Country of origin
- European Union
- Nominal capacity
- 100
- Diameter
- 43 mm
- Thread type
- 28/410
- Height
- 111,3 mm
Plastic pump, white, dip tube 130 mm, 28/410
Product documentation
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.










