PLASTIC BOTTLES
Blue Plastic Bottle, White Pump, 200 ml
Pack size200 ml250 ml
Plastic bottle, blue, with white pump, 200 ml The blue 200 ml bottle with a white pump is designed for dispensing liquid and medium-thick products that are taken out repeatedly in small amounts: body lotion, liquid hand… full description
Lowest price in the last 30 days: €0.94
Total for 1 pcs: €0.94
Quantities add up across all combinations of this bottle.
Product description
Plastic bottle, blue, with white pump, 200 ml
The blue 200 ml bottle with a white pump is designed for dispensing liquid and medium-thick products that are taken out repeatedly in small amounts: body lotion, liquid hand soap, shampoo, shower gel, cleansing oil or massage oil. The bottle is made of PET and is lightweight, so it works well in the bathroom as well as on the go.
The PP pump screws onto the 24/410 neck finish and delivers approximately 1 ml per press, so the dose is consistent even with everyday use. The set is approved for direct food contact and declared suitable for cosmetic products.
What the set is suitable for
- Body lotion and light creams – one press delivers the amount needed for your hands or face; the contents are not scooped out with your fingers and stay in the packaging, protected from air and impurities.
- Liquid soap, shampoo, shower gel – the 200 ml volume is enough for regular use at the sink or in the shower.
- Cleansing, massage or body oil – the pump dispenses oil without spilling and the neck stays clean.
- Homemade oils, syrups and dressings – the set is also suitable for the kitchen, for dispensing liquid foods in small amounts.
The bottle and the pump each have their own certificate for direct food contact and a declaration of suitability for cosmetics, so the set as a whole can be used for both types of contents.
Nominal volume and filling
The nominal volume is the amount the packaging is intended for under normal filling. The physical volume of the bottle up to the neck is larger. The difference provides a reserve for the dip tube and the pump body, which push part of the contents upwards when screwed on, and for the expansion of the contents when the temperature changes. The bottle is therefore filled to 200 ml, not to the brim.
For the first filling, pour in 200 ml, screw on the pump and check the level. If the contents rise to just below the neck after tightening, reduce the amount slightly for the next filling so that the pump does not draw in air and the neck stays clean.
How to use the set
Before the first filling, wash the bottle and the pump with warm water, disinfect them with isopropyl alcohol or ethanol and leave them to dry completely. Before fitting the pump, press it several times without contents so that the water runs out of the dip tube.
The pump handles liquid to medium-thick contents. Very thick creams and balms will not pass through the dip tube or will be dispensed unevenly. For thin water-based contents, such as toners, the pump delivers a larger dose onto the palm than is needed, so a fine mist sprayer is worth considering instead. The dip tube of the pump is longer than the height of the bottle, so shorten it with sharp scissors before fitting so that it reaches just above the bottom. Before transport, tighten the pump firmly and transport the bottle upright.
Fill with contents cooled to room temperature. The bottle is not designed for hot filling; an emulsion or oil taken straight from a water bath may deform it.
PET is not intended for aggressive chemicals. For products with a high proportion of alcohol, essential oils or solvents, we recommend testing how the bottle and the pump behave with your specific formulation before filling the whole volume.
Good to know
Once empty, you can wash the set and fill it again. Wash the bottle and the pump, rinse the dip tube with clean water and disinfect them again before the next filling. Oil residues are removed by warm water with washing-up liquid.
The bottle is made of PET and the pump of PP; both parts go in plastic recycling. Before disposal, take the set apart and sort each part separately.
Other closures with the same neck type, which is stated in the parameters, can also be fitted to the bottle. You can find ready-made combinations of the bottle and closure in the Handymade range. If you make your own combination, we recommend checking the tightness, dispensing and behaviour of the packaging with your specific formulation.
Frequently asked questions
Parameters
Plastic bottle, blue, 24/410, without closure, 200 ml
- Product colour
- Blue
- Country of origin
- European Union
- Nominal capacity
- 200
- Diameter
- 47 mm
- Thread type
- GL24
- Height
- 150 mm
Product documentation
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.



































































