PLASTIC BOTTLES
Rounded Clear Plastic Bottle, Black Lotion Pump With Glossy Silver Collar, 200 ml
Pack size100 ml150 ml200 ml300 ml
Description This set of a 200 ml PET bottle with a black and silver pump is designed for liquid and semi-liquid cosmetic products that are dispensed by pressing the pump. full description
Lowest price in the last 30 days: €1.27
Total for 1 pcs: €1.27
Quantities add up across all combinations of this bottle.
Product description
Description
This set of a 200 ml PET bottle with a black and silver pump is designed for liquid and semi-liquid cosmetic products that are dispensed by pressing the pump. It suits liquid soaps, shower gels, shampoos, body lotions, liquid hand creams and massage oils. The product is dispensed without unscrewing the closure, no air or fingers get into the bottle, and the dose stays approximately the same with every press.
PET is lightweight and unbreakable, so the set holds up by the sink, in the shower and when travelling. The clear wall shows the colour of the product and the amount remaining. The pump combines black PP plastic with a silver aluminium element and looks neat even where the packaging is always on display. Both the bottle and the pump are declared suitable for contact with cosmetic products, and the declaration of conformity is available with the product.
What the set is suitable for
- Liquid soaps and shower gels – the pump dispenses enough for one wash without any contact with the neck, which you will appreciate especially where the packaging is used by several people.
- Shampoos and liquid conditioners – the clear wall shows how much product is left.
- Body lotions and lighter creams – the consistency must be liquid enough to pass through the dip tube and the pump. Thick creams cannot be pushed out through the pump.
- Massage and body oils – oils pass through the pump easily. For formulations with a high proportion of essential oils, we recommend testing how the plastic behaves on a small quantity first.
- Cleansing emulsions and make-up remover milks – a measured amount in the palm makes application easier and reduces waste.
Filling and capacity
The nominal volume is the volume the packaging is designed for under normal filling. The brimful capacity given in the parameters is the physical volume of the bottle up to the neck. The difference between them is a reserve for the dip tube of the pump and for the air above the surface. The bottle should therefore be filled to the nominal volume, not to the brim, otherwise the contents will be pushed out through the neck when the pump is screwed on.
One press of the pump dispenses approximately 1 ml of product. With thicker formulations or a weaker press, the dose may be smaller. After filling and screwing on the pump, press it several times without dispensing so that the dip tube and the mechanism fill up and the product starts to flow smoothly.
When assembling for the first time, check the length of the dip tube in the bottle. The tube should reach just above the bottom so that it draws up almost all of the contents. If it rests on the bottom and bends, shorten it with a sharp knife using a straight cut.
Good to know
Before the first filling, we recommend washing the bottle and the pump, rinsing them with isopropyl alcohol or ethanol and leaving them to dry completely. Residual water in the dip tube or in the bottle would dilute the product and, in water-based formulations, increases the demands on preservation.
The clear wall offers no protection from light. Products with sensitive ingredients, for example a higher proportion of unsaturated vegetable oils or dyes that fade in light, are better filled into an amber or dark container. Store the clear bottle away from direct sunlight.
PET must not be filled with hot contents. Let emulsions, gels and soaps cool to room temperature before filling, as heat deforms the material and may affect the tightness of the thread. Do not expose the bottle to aggressive chemicals or concentrated solvents. For products containing essential oils, alcohol or citrus ingredients, we recommend testing compatibility on a small quantity and checking whether the plastic becomes cloudy or soft.
The pump is not designed for products with solid particles, such as scrubs with sugar, salt or crushed kernels. The particles get caught in the valve and the pump stops dispensing.
The bottle with a 24/410 neck finish can also be combined with other closures of the same thread, which you can find in the Handymade range together with ready-made sets. When making your own combination, we recommend testing the tightness, the dispensing and the behaviour of the packaging with your specific formulation.
Once the bottle is empty, wash it with warm water and a cleaning product. First pump clean warm water through the pump and then alcohol, so that residues of the product are rinsed out of the dip tube and the valve, and leave all parts to dry. The PET bottle belongs in plastic recycling. The pump contains an aluminium part and PP plastic, so separate it from the bottle before disposal.
Frequently asked questions
Parameters
Plastic bottle, clear round, 24/410, 200 ml, without cap
Product documentation
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.


































































