PLASTIC BOTTLES
White Plastic Bottle, White Spray With Glossy Silver Collar, 300 ml
Pack size100 ml150 ml200 ml250 ml300 ml
The white plastic 300 ml bottle with a mini trigger sprayer is a set for thin liquid preparations applied as a fine mist: face and body toners, hydrosols, hair sprays, air fresheners, or solutions for disinfecting hands… full description
Lowest price in the last 30 days: €1.53
Total for 1 pcs: €1.53
Quantities add up across all combinations of this bottle.
Product description
The white plastic 300 ml bottle with a mini trigger sprayer is a set for thin liquid preparations applied as a fine mist: face and body toners, hydrosols, hair sprays, air fresheners, or solutions for disinfecting hands and surfaces. The bottle and the sprayer share the same 24/410 neck finish, so you do not have to look for a matching closure. The white wall of the bottle dims the light reaching the contents, and the plastic is light and does not break when dropped, which suits the bathroom, a handbag and travel.
The sprayer has a white head and a silver glossy collar, which gives the packaging a clean, unobtrusive look that suits your own label or simple black and white graphics. The set is declared suitable for contact with cosmetics. The certificate for direct contact with food applies to the bottle only; the sprayer does not have it, so the assembly as a whole is intended for cosmetic and technical preparations, not for food.
What the set is suitable for
- Toners and hydrosols – thin water-based solutions spray evenly, and the 300 ml volume suits a larger home pack or salon use.
- Hair sprays and mists – low-viscosity solutions, for example detangling sprays, sea salt sprays or sprays with a hydrosol, are applied directly to the hair without touching it with your hands.
- Disinfectant solutions – alcohol-based preparations for hands and surfaces. With a higher content of alcohol or essential oils, first check how the plastic behaves with your specific recipe.
- Fabric and air fresheners – water-alcohol blends with a fragrance composition or essential oils at low concentration.
- Auxiliary solutions in production – alcohol for spraying the surface of soap or foam in cold process soap, water for adjusting consistency, solutions used when working with pigments.
How the sprayer dispenses
The mini trigger sprayer works by pressing the head. The piston draws the contents up through the tube from the bottom of the bottle and pushes them out through the nozzle as a fine mist. One dose is small, approximately 0.12 ml, so it suits repeated application over a larger area, for example on the face, hair or fabric. Thicker liquids, oils with higher viscosity and emulsions either do not pass through the nozzle at all or come out as a stream instead of a mist. This set is for liquids with a consistency close to water. Before first use, press the head several times to prime it, so that the tube fills and the mist becomes even.
Preparations with undissolved particles, remnants of plant material or a flocculating preservative clog the nozzle and the valve. Filter aqueous extracts and hydrosols before filling, and do not fill the sprayer with emulsions or thickened serums.
Nominal and total volume
The nominal volume of 300 ml is the amount the bottle is designed for under normal filling. The physical volume of the bottle up to the neck is slightly larger. The difference is a reserve for the tube and the body of the sprayer, which push part of the contents upwards when screwed on, and for the expansion of the liquid with temperature changes. The bottle is filled to the nominal volume, not to the brim. If overfilled, the contents will spill out through the neck when you screw on the sprayer, and the thread may then leak.
When filling, leave free space in the neck at least as high as the thread. Tighten the sprayer by hand, without excessive force, and check that it is sealed by turning the bottle upside down over the sink.
Good to know
Before first filling, wash the bottle and the sprayer in warm water with detergent, rinse, disinfect with isopropyl alcohol or ethanol and leave to dry completely. Spray alcohol through the sprayer from the inside too, that is, draw it up and spray it out several times. Residual water in the tube would dilute the contents and, in anhydrous alcohol recipes, can cause cloudiness.
The set withstands repeated use. When refilling, proceed in the same way as before first filling and spray clean water or alcohol through the nozzle so that no residues of the previous preparation remain in it, especially if it contained a fragrance composition or oil.
Do not fill the bottle with hot contents. Fill the water phase, the alcohol and the finished toner once they have cooled to room temperature, and do not expose the packaging to heat or direct sunlight. Concentrated essential oils, strong solvents and aggressive chemicals can damage both the plastic of the bottle and the seal of the sprayer. For such recipes we recommend a trial filling and a check after several weeks.
The bottle has a 24/410 neck finish, so it can also be closed with another closure of the same neck type from the Handymade range, for example when you want to store part of your production without the sprayer. If you combine parts yourself, check the tightness and the behaviour of the packaging with your specific formulation.
The bottle is made of PET and is recycled as plastic. The sprayer combines polypropylene and an aluminium collar, so separate it from the bottle before disposal.
Frequently asked questions
Parameters
Plastic bottle, white, 24/410, without cap, 300 ml
Product documentation
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.

































































