PLASTIC BOTTLES
White Plastic Bottle, White Lotion Pump With Glossy Gold Collar, 300 ml
Pack size100 ml150 ml200 ml250 ml300 ml
This white plastic bottle with a nominal volume of 300 ml and a white and gold pump is designed for products that are dispensed with a one-handed press: body lotions, liquid soaps, shampoos or shower gels. full description
Lowest price in the last 30 days: €1.45
Save €0.03 with this set
Total for 1 pcs: €1.45
Quantities add up across all combinations of this bottle.
Product description
This white plastic bottle with a nominal volume of 300 ml and a white and gold pump is designed for products that are dispensed with a one-handed press: body lotions, liquid soaps, shampoos or shower gels. The bottle is made of PET, is light and does not break when dropped, so it works well in the bathroom by the sink as well as when packing for travel. The white bottle with a gold pump head can be matched with printing and with other packaging from the same range.
The set is declared suitable for contact with cosmetic products. Only the bottle has a separate certificate for direct food contact; the pump does not, so the set as a whole is intended for cosmetics.
What it is suited for
- Body lotions and lighter creams – the pump draws thinner emulsions without problems and the contents stay in the closed bottle, where they do not come into contact with fingers.
- Liquid soaps and shower gels – the 300 ml volume matches a standard size for the sink or the shower.
- Shampoos and conditioners with a liquid to medium-thick consistency – for thicker formulations we recommend a test fill.
- Cleansing milks and make-up remover emulsions – when working with wet hands, dispensing by pressing is more convenient than unscrewing a cap.
Pump and dispensing
One press dispenses approximately 1 ml of contents. The actual amount varies with the viscosity of the product: with thinner liquids the dose tends to be fuller than with thick emulsions. Before first use, prime the pump by pressing it several times until the tube fills and the contents start to flow evenly.
The dip tube is supplied with extra length and exceeds the height of the bottle. Before filling, hold it against the bottle and trim it with sharp scissors using a straight cut so that its end touches the bottom. An angled cut makes the tube bend in the corner of the bottom and the pump stops drawing the last millilitres.
After filling, tighten the pump head by hand only. Excessive force damages the 24/410 thread on the PET bottle and the closure then leaks even though it is tightened “all the way”.
Volume and filling
The nominal volume is the amount the bottle is designed for under normal filling. The brimful volume is the physical volume up to the neck and is slightly larger. The difference between them is a reserve for the tube and pump body, which push part of the contents upwards when screwed on, and for the expansion of the contents when the temperature changes. Fill the bottle to the nominal 300 ml, not up to the neck. An overfilled bottle overflows as soon as the pump is fitted.
Let emulsions and gels cool to room temperature before filling. PET is not intended for hot filling, and warm contents may deform the bottle wall.
Good to know
- Preparation before first filling – wash the bottle, disinfect it with isopropyl alcohol or ethanol and leave it to dry completely with the neck facing down. Flush the pump several times with clean water, then with alcohol, and let it dry as well.
- Viscosity of the contents – thick creams, balms and products that solidify as they cool are not drawn by the pump, or are dispensed unevenly. Check that the consistency is suitable on a test batch before you fill the whole run.
- Essential oils and solvents – the packaging is not intended for aggressive chemicals. For formulations with a higher proportion of essential oils, alcohol or solvents, we recommend checking the behaviour of the bottle and of the pump seal with your specific formulation.
- Reuse – after thorough cleaning, the bottle and the pump can be filled again. When changing the contents, check the tube, where residues of the previous product remain.
- Other closures – other closures with a 24/410 neck finish also fit the bottle, and you can find them, together with ready-made combinations, in the Handymade range. If you make your own combination, check the seal and the dispensing with your specific formulation.
- Recycling – the bottle is made of PET and the pump combines polypropylene and aluminium, so separate them and sort them individually before disposal.
Do not fill the bottle and pump set with oils, syrups or other foods. Only the bottle itself has the food-contact certificate; the pump does not.
Frequently asked questions
Parameters
Plastic bottle, white, 24/410, without cap, 300 ml
Product documentation
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.
































































