ALUMINUM BOTTLES
Aluminium bottle, black-gold matte pump, 50 ml
The set consisting of a 50 ml aluminium bottle and a plastic pump in a matte black and gold finish is intended for liquid and semi-liquid cosmetic products that are dispensed by pressing the pump. full description
Lowest price in the last 30 days: €2.69
Save €0.01 with this set
Total for 1 pcs: €2.69
Quantities add up across all combinations of this bottle.
Product description
The set consisting of a 50 ml aluminium bottle and a plastic pump in a matte black and gold finish is intended for liquid and semi-liquid cosmetic products that are dispensed by pressing the pump. Aluminium blocks light, is lightweight and unbreakable, which you will appreciate with light-sensitive products and when travelling. The pump dispenses approximately the same amount with each press. The contents do not need to be poured out through the neck, and fingers do not come into contact with them during use.
This packaging suits body lotions, lighter face and hand creams, liquid cleansing gels, light serums, or hand products that sit by the sink or on the bedside table. The 50 ml volume corresponds to a travel size or a smaller face product. Both the bottle and the pump have a 24/410 neck finish, so the parts fit together without any further adjustment.
The bottle and the pump are declared as suitable for contact with cosmetic products, and the set is intended for cosmetics. A declaration of conformity is issued for each component.
What it is suitable for
- Creams and body lotions – the pump handles emulsions that can be drawn up through the dip tube. With thicker creams, test whether the pump pushes out the entire contents.
- Serums and light fluids – the pump dispenses thin water-based or oil-based contents quickly, but at low viscosity the contents may drip from the nozzle.
- Cleansing gels and liquid soaps – dispensing without hands touching the contents suits products used several times a day.
Nominal and total volume
The nominal volume of 50 ml is the volume the bottle is designed for in normal filling. The total volume to the brim is larger. The difference provides room for the submerged part of the pump with its dip tube and for the expansion of the contents when the temperature changes. The bottle should therefore be filled up to the nominal volume. If it were filled right up to the neck, part of the contents would be pushed onto the thread when the pump is screwed in and could leak.
One pump dose corresponds to approximately 1.3 ml. You can use this value when calculating consumption or writing instructions for use. With thick or very thin contents, the actual dose may differ.
Good to know
The pump is supplied with a 220 mm dip tube that is designed to fit several bottle heights. Before first use, shorten it so that, once screwed in, it reaches just above the bottom of the bottle. A tube resting on the bottom may bend and stop drawing up the contents. A tube that is too short, on the other hand, leaves part of the contents at the bottom.
Before the first filling, wash the bottle and the pump and let them dry completely. Rinse the pump by pumping clean water through it and let it drain with the dip tube pointing downwards.
When transporting a full bottle, check that the contents are not pushed out if the pump is pressed in a bag. For shipments, you can use a separate cap with the same 24/410 neck finish and pack the pump separately.
Always test how the bottle and the pump behave with your specific formulation on a sample. This applies especially to products with a higher content of essential oils or alcohol, or with a low pH, which can affect the plastic parts of the pump.
After thorough washing and drying, the bottle and the pump can be reused. When refilling repeatedly, check that the pump draws up smoothly and that the thread seals properly. Aluminium is a metal packaging material, and the pump is made of several materials, including the metal parts of the mechanism, so separate it from the bottle before recycling.
The bottle can also be combined with other closures with a 24/410 neck finish from the Handymade range. If you make your own combination, check the seal and the dispensing with your specific contents.
Frequently asked questions
Parameters
Aluminium bottle, 24/410, 50 ml
Product documentation
- DrawingTechnical drawing
- PDF ↓
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.



















































