PLASTIC BOTTLES
Rounded Clear Plastic Bottle, Black Lotion Pump With Matte Gold Collar, 500 ml
Pack size100 ml150 ml200 ml300 ml500 ml
A clear plastic PET bottle with a volume of 500 ml and a black and gold matte pump with a 24/410 neck finish make a ready-to-use set for products dispensed by pressing a pump: body lotion, liquid hand soap, shower gel,… full description
Lowest price in the last 30 days: €1.35
Total for 1 pcs: €1.43
Quantities add up across all combinations of this bottle.
Product description
A clear plastic PET bottle with a volume of 500 ml and a black and gold matte pump with a 24/410 neck finish make a ready-to-use set for products dispensed by pressing a pump: body lotion, liquid hand soap, shower gel, shampoo or conditioner. The clear plastic shows the colour of the contents and how much is left in the bottle. The dark head with a matte finish and the gold detail on the neck give the set a look that holds its own on a bathroom shelf as well as in a salon. Both the bottle and the pump are declared as suitable for contact with cosmetic products.
PET is lightweight and shatter-resistant, which matters with half a litre of contents. The bottle can be used in the shower, at the sink and when carried between premises. The dip tube of the pump reaches right to the bottom, so the contents can be used up without turning the bottle over or shaking it.
What the set is suitable for
- Liquid soap and shower gel – one press dispenses approximately 1.3 ml, which corresponds to a standard dose of hand soap. For shower gel, expect several presses.
- Shampoo and conditioner – dispensed with one hand without unscrewing a cap, wet hands are not a problem for the packaging, and the bottle will not break if dropped in the shower.
- Body lotion and light creams – the pump draws up liquid to medium-thick emulsions. Thick creams and butters do not belong in the pump, as they stay in the tube and the mechanism cannot push them through.
- Massage and body oils – the pump also works with oil bases without a water phase.
Filling and dispensing
The bottle is filled to the nominal volume, that is, the amount the packaging is designed for in normal filling. The brimful volume stated in the parameters is the physical volume up to the neck. The difference between the two values is a reserve for the submerged dip tube of the pump and for the expansion of the contents when the temperature changes.
Before the first filling, wash the bottle, disinfect it with isopropyl alcohol or ethanol and leave it to dry completely. Pump warm water through the pump several times and leave it to dry as well. After filling, fit the pump, tighten it by hand and draw the contents into the tube with several presses. If the tube bends at the bottom after screwing on, shorten it with a sharp knife using a diagonal cut so that it ends just above the bottom.
Before first use, lay the filled set on its side on a paper towel and leave it there for several hours. You will find out whether the closure seals with your formulation and whether the pump drips after pressing.
Good to know
Clear PET lets light through. Products with sensitive ingredients, for example oils with a high proportion of unsaturated fatty acids, vitamins or natural dyes, lose quality faster in it on a sunny windowsill than in amber or opaque packaging. Store such formulations away from direct light or choose a dark bottle.
Hot mixtures must not be poured into PET. Emulsions and soaps are filled only after cooling to room temperature, as at higher temperatures the plastic may deform. Caution is also needed with products with a high proportion of alcohol or undiluted essential oils, which may damage PET and the plastic seals of the pump over the long term. In these cases, test a small amount over several weeks before filling the whole batch.
The pump is designed for liquid to medium-thick products. Watery toners or hydrosols run out of it in a stream and part of the product stays on your hands, so a fine mist sprayer is more suitable for them. Other closures with the same neck type from the Handymade range can also be fitted to the bottle. If you make your own combination, check the seal and dispensing with your specific formulation.
The pump contains metal parts in its mechanism. With products with a low pH or a high salt content, watch whether the colour of the contents changes over time and whether dispensing gets worse.
The bottle can be used repeatedly; simply wash and disinfect it in the same way as before the first filling. When you change the formulation, it is better to replace the pump, as fragranced products leave their scent in the plastic. For disposal, separate the pump from the bottle. The bottle is made of recyclable PET, while the pump combines several types of plastic and metal.
Frequently asked questions
Parameters
Plastic bottle, clear round, 24/410, 500 ml
- Product colour
- Clear
- Country of origin
- European Union
- Nominal capacity
- 500
- Brimful capacity
- 522 ml
- Diameter
- 61,5 mm
- Thread type
- 24/410
- Height
- 206,5 mm
Product documentation
- DrawingTechnical drawing
- PDF ↓
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.














































