ALUMINUM BOTTLES
Aluminium Bottle, White Lotion Pump With Glossy Silver Collar, 200 ml
Pack size50 ml100 ml200 ml225 ml
The aluminium bottle with a pump, holding 200 ml , is intended for liquid and semi-liquid cosmetic products that are dispensed by pressing the pump head, without unscrewing the closure and pouring. full description
Lowest price in the last 30 days: €3.28
Total for 1 pcs: €3.28
Quantities add up across all combinations of this bottle.
Product description
The aluminium bottle with a pump, holding 200 ml, is intended for liquid and semi-liquid cosmetic products that are dispensed by pressing the pump head, without unscrewing the closure and pouring. Aluminium does not let light through, so the contents are protected from light throughout use. The bottle is suitable for body lotions, face emulsions, liquid soaps, shower gels, shampoos, conditioners and massage oils, that is, for anything with a consistency ranging from water to a thicker lotion that is dispensed in small amounts. The silver bottle with a white and silver pump has a uniform look that needs no further finishing.
What the set includes
- Aluminium bottle 200 ml with 24/410 neck finish – opaque, lightweight and unbreakable.
- Plastic pump 24/410, white and silver – head with dip tube, plastic body with an aluminium element. One press dispenses approximately 1 ml.
How to use the pump
The pump is screwed onto the neck of the filled bottle. Before the first use, press the head several times without dispensing until the contents are drawn up through the tube into the mechanism. The volume of one dose is approximate and varies with the thickness of the contents. Water, toners, oils and emulsions with the consistency of a lotion pass through smoothly, while thicker emulsions require a firmer press. For creams that do not flow after being scooped, we recommend first testing whether the pump can draw them up at all.
If the dip tube reaches the bottom and rests against it, shorten it with a sharp knife using a diagonal cut. An angled end does not stick to the bottom and draws up even the last remnants of the contents.
Volume and filling
The nominal volume of 200 ml is the volume the bottle is designed for under normal filling. The brimful capacity given in the parameters is the physical volume up to the neck. The difference between them leaves room for the tube and the pump mechanism, which takes up part of the space once screwed on, and for the expansion of the contents with changes in temperature. Fill to the nominal volume, not to the brim. The bottle is narrow and tall, so a funnel or a bottle with a long neck is suitable for filling, otherwise the contents run down the outer wall.
Good to know
Declared suitability differs for each component of this set. The aluminium bottle has a declaration of suitability for contact with cosmetic products, while the pump as a separate component has no such declaration, so the set as a whole is not declared suitable for contact with cosmetics. Neither the bottle nor the pump is approved for contact with food.
The set is not intended for food, drinks, or homemade oils and syrups. It is intended for cosmetic and technical products.
Before the first filling, wash the bottle with warm water, disinfect it with isopropyl alcohol or ethanol and leave it to dry completely upside down. Rinse the pump by immersing the tube in the disinfectant and pressing several times, then pump clean water and air through it in the same way. Contents that dry inside the mechanism will block the pump, so always rinse it before a longer break.
The aluminium bottle does not deform during normal use, but strong pressure on the wall will dent it permanently. Fill it only with a cooled emulsion, not with a hot phase straight from the pot. For contents with a higher proportion of essential oils, alcohol or solvents, we recommend checking how the plastic parts of the pump and the seal behave, and leaving the filled set to stand on its side for several days.
Closures with the same 24/410 neck finish and ready-made combinations of the bottle with a different closure can be found in the Handymade range. If you combine the parts yourself, we recommend checking the tightness, dispensing and behaviour of the packaging with your specific formulation.
Once empty, the aluminium bottle belongs with metals and is fully recyclable. The pump is a combination of plastic and metal, so separate it from the bottle before disposal.
Frequently asked questions
Parameters
Aluminium bottle, 24/410, 200 ml
Product documentation
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.






















































