ALUMINUM BOTTLES
Aluminium Bottle, White Lotion Pump With Overcap, Glossy Gold, 100 ml
Pack size50 ml100 ml200 ml225 ml
An aluminium bottle with a volume of 100 ml and a plastic pump with an overcap together form ready-to-use packaging for liquid and semi-liquid cosmetic products that are used in small doses. full description
Lowest price in the last 30 days: €3.22
Total for 1 pcs: €3.22
Quantities add up across all combinations of this bottle.
Product description
An aluminium bottle with a volume of 100 ml and a plastic pump with an overcap together form ready-to-use packaging for liquid and semi-liquid cosmetic products that are used in small doses. Opaque aluminium keeps light away from the contents and the bottle does not break when dropped, so it is suitable for travel, for the bathroom and for a handbag. The pump dispenses the same amount with every press, the contents do not spill and only what is being applied comes into contact with the hand.
The set consists of a bottle with a 24/410 neck finish and a matching pump in a white and gold design. The removable overcap covers the pump head when the packaging is not in use. Both components are declared as suitable for contact with cosmetic products, and you will find the declaration of conformity with the product.
What the set is suitable for
- Face and body oils – the pump replaces the dropper where an oil is used daily and in larger amounts, for example on the body or for massage.
- Serums and light emulsions – a small dose per press corresponds to the amount that is usually applied to the face. The contents stay in the closed packaging without contact with your fingers.
- Body lotions and liquid creams – thinner emulsions pass through the pump without problems, and you can handle the aluminium bottle with wet hands without worrying that it will break.
- Hair oils and leave-in care – the opaque packaging suits products containing vegetable and essential oils, which age faster in light.
How to use the pump
One press dispenses approximately 0.2 ml of the contents, so you can easily measure a dose by the number of presses. After filling the bottle and screwing on the pump, press the pump head several times to prime it until the dip tube and the mechanism fill and the product starts to come out. The dip tube should reach the bottom of the bottle so that the contents are used up as completely as possible.
The dip tube is longer than the bottle, so shorten it with a sharp knife or scissors using a diagonal cut. The bevelled end does not stick to the bottom, and the pump draws up the contents right down to the last layer.
The pump works best with liquid to medium-thick textures. With thick creams, balms or gels with a higher viscosity, test a small amount to check that the mechanism draws up the contents and that the dose does not vary.
Volume and filling
The nominal volume of 100 ml is the volume the bottle is intended for under normal filling. The brimful volume given in the parameters is the physical volume up to the neck. The difference between them is a reserve for the dip tube and the pump mechanism, and for the expansion of the contents when the temperature changes.
Fill the bottle to the nominal volume, not to the brim. If you fill it to the neck, the pump pushes part of the contents out when it is screwed on, and the thread becomes sticky with product.
Good to know
- Preparation before the first filling – wash the bottle and the pump, disinfect the inside with isopropyl alcohol or ethanol and let it dry completely. Residual water in the dip tube would get into the first dose.
- Compatibility with the formulation – the packaging is declared for cosmetic products, but its behaviour with a specific recipe varies depending on the composition. For water-based and acidic products, or a higher proportion of essential oils or solvents, fill a test bottle and after some time check the contents, the inside of the bottle and the tightness of the pump.
- Aluminium and mechanical stress – the bottle does not break, but it may dent if squeezed hard or dropped on an edge. When dispensing, hold the bottle; do not squeeze it.
- Overcap – protects the pump head from dust and accidental pressing. When transporting the packaging in luggage, leave it on so that the pressure of surrounding items does not press the pump head.
- Other closures – the bottle has a 24/410 neck, and you will find closures with the same neck finish and ready-made combinations in the Handymade range. If you make your own combination, check the tightness and dispensing with the specific formulation.
- Reuse – after washing and disinfection, the set can be filled again. When sorting waste, separate the pump from the bottle.
Frequently asked questions
Parameters
Aluminium bottle, 24/410, 100 ml
White Lotion Pump With Overcap, 24/410, Glossy Gold, 200 mm
- Country of origin
- European Union
- Diameter
- 27,5 mm
- Thread type
- 24/410
- Height
- 45 mm
- Tube length
- 220 mm
- Dose
- 0,2 ml
Product documentation
- DrawingTechnical drawing
- PDF ↓
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.





















































