ALUMINUM BOTTLES
Aluminium Bottle, White Lotion Pump With Overcap, Glossy Gold, 200 ml
Pack size50 ml100 ml200 ml225 ml
An aluminium bottle with a pump protects its contents from light and dispenses them at the press of the pump head, without unscrewing the closure. full description
Lowest price in the last 30 days: €3.42
Total for 1 pcs: €3.42
Quantities add up across all combinations of this bottle.
Product description
An aluminium bottle with a pump protects its contents from light and dispenses them at the press of the pump head, without unscrewing the closure. Metal does not let light through, so the set is suitable for face and body oils, serums, fluids and light emulsions, whose ingredients lose their effectiveness when exposed to light. Aluminium is lightweight and does not break when dropped, so the bottle holds up on the edge of the bath as well as in a travel bag.
The pump has a white body with a gold detail and comes with an overcap that covers the pump head, protects it from dust and prevents accidental pressing. The bottle is silver, with a nominal volume of 200 ml and a 24/410 neck finish, and the pump has the same thread. The set is declared suitable for contact with cosmetic products.
What the set is suitable for
- Face and body oils – the opaque packaging slows the degradation of light-sensitive oils, and the pump dispenses a small amount without spilling.
- Serums and fluids – a dose of approximately 0.2 ml per press suits concentrated products that are applied in small amounts.
- Light emulsions and body lotions – the dose is relatively small, so with normal use expect several presses.
- Bathroom products – the metal bottle does not break, and a 200 ml fill lasts a long time.
How the pump works
One press dispenses approximately 0.2 ml of the contents. The actual amount depends on the consistency of the product, so with thicker emulsions it is worth checking the dose. The contents are drawn up by a dip tube that is longer than the bottle. After screwing on the pump, therefore, check that the tube does not rest on the bottom or bend. If it is too long, trim it with a sharp knife so that it ends just above the bottom.
After screwing on, the pump does not dispense the contents straight away. First it needs to be pressed several times to fill the dip tube and the mechanism, after which it dispenses evenly. Pumps of this type draw very thick creams and gels poorly. With very thin water-based solutions, check that the pump head does not drip after pressing. We recommend testing the behaviour with your specific formulation on one piece before filling a larger batch.
Before the first filling, screw the pump onto the empty bottle and check the length of the dip tube. It is easier to trim it to size before filling than after.
Volume and filling
The nominal volume is the amount the bottle is designed for with normal filling. The total brimful volume given in the parameters is the physical volume up to the neck. The difference between them is a reserve for the dip tube and the pump mechanism and for the expansion of the contents with changes in temperature. The bottle should therefore be filled to the nominal volume, not to the brim. If it is overfilled, the contents are forced out through the thread when the pump is screwed on.
We do not have information on the internal coating of the aluminium bottle. We recommend checking compatibility with products with a low pH, a higher electrolyte content or essential oils in the finished formulation, for example by a trial filling lasting several weeks.
Good to know
Before the first filling, wash the bottle and the pump, disinfect them with isopropyl alcohol or ethanol and leave them to dry completely. Rinse the pump by pressing it several times in clean water and then pumping it dry until all the water has been expelled. Residual moisture in the dip tube could dilute the contents or encourage the growth of microorganisms.
Aluminium does not break under a stronger impact, but it can be dented. A dented bottle wall does not affect the function of the pump, only the appearance. After washing and drying, the set is suitable for repeated use. The pump mechanism may lose its seal after longer use, so check it each time you fill the bottle again.
Closures with the same neck type, as well as ready-made packaging and closure combinations, can be found in the Handymade range. If you are making your own combination, we recommend checking the seal, the dispensing and the behaviour of the packaging with your specific formulation.
The set is intended for cosmetic products and is not declared for contact with food. The aluminium bottle is recycled as metal. The pump combines PP plastic with metal parts, so separate it from the bottle when disposing of it.
Frequently asked questions
Parameters
Aluminium bottle, 24/410, 200 ml
White Lotion Pump With Overcap, 24/410, Glossy Gold, 200 mm
- Country of origin
- European Union
- Diameter
- 27,5 mm
- Thread type
- 24/410
- Height
- 45 mm
- Tube length
- 220 mm
- Dose
- 0,2 ml
Product documentation
- DrawingTechnical drawing
- PDF ↓
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.






















































