PLASTIC BOTTLES
Rounded Clear Plastic Bottle, Type B, Transparent Plastic Pump, 300 ml
Pack size100 ml200 ml300 ml500 ml
The plastic bottle with pump has a volume of 300 ml and is designed for filling with liquid and medium-thick cosmetic products that are dispensed by pressing. full description
Lowest price in the last 30 days: €1.05
Total for 1 pcs: €1.46
Quantities add up across all combinations of this bottle.
Product description
The plastic bottle with pump has a volume of 300 ml and is designed for filling with liquid and medium-thick cosmetic products that are dispensed by pressing. The bottle is made of PET and closed with a PP pump with a 24/410 neck finish. Both parts are clear, so you can see the contents and the amount remaining at a glance. The set is sold as a whole – simply fill it and screw it on.
PET is lightweight and unbreakable, which you will appreciate especially for shower and bathroom products or for larger batches that are shipped to customers. The pump dispenses approximately the same amount each time without unscrewing, so the contents do not come into contact with fingers and the risk of contamination is reduced.
Suitable uses
- Body lotions and light creams – the pump handles emulsions of liquid to medium-thick consistency; thick creams are difficult to dispense through it.
- Liquid soaps, shower gels and shampoos – the 300 ml volume corresponds to a standard bathroom pack, and dispensing with a single press is the most convenient option for rinse-off products.
- Conditioners and hair masks – if they are not too thick, the pump dispenses them without them running down the walls of the bottle.
- Cleansing gels and facial milks – the clear bottle shows off both clear and coloured gels when you want the contents on display.
Volume and filling
The nominal volume is the amount the bottle is designed for in normal filling. The brimful capacity is the physical volume up to the neck and is stated in the parameters. The difference between them leaves room for the dip tube and the body of the pump. The bottle should therefore be filled up to the nominal volume, not to the brim, otherwise the contents will overflow when you screw on the pump.
One press dispenses approximately 1.4 ml. With this figure you can estimate the number of doses from a full bottle, prepare instructions for use or compare consumption with other packs.
The dip tube of the pump should reach close to the bottom of the bottle so that the contents can be used up as much as possible. If it protrudes and bends after fitting, shorten it with a sharp knife or scissors using a straight cut. Before first use, press the pump several times until the tube and piston fill and the product starts to come out evenly.
Good to know
The set is declared suitable for contact with cosmetic products, and the declarations of conformity for both the bottle and the pump are available with the product.
Clear plastic does not protect the contents from light. Products with vegetable oils, essential oils or light-sensitive active ingredients should therefore be stored out of direct sunlight, or you can choose dark packaging for them. For formulations with a higher proportion of alcohol, essential oils or solvents, we recommend testing the behaviour of the PET and the pump seals with your specific recipe before a larger batch.
Do not fill the bottle with hot contents, as PET deforms at higher temperatures. Allow emulsions and gels to cool to room temperature before filling.
Before the first filling, wash the bottle and the pump, disinfect them with isopropyl alcohol or ethanol and leave them to dry completely. Residual water in the tube or at the bottom would dilute the first dose of the product and increase the risk of microbial contamination.
The set can be used repeatedly. After emptying, rinse the bottle and the tube with warm water, pump clean water through the pump several times and leave it to dry. For recycling, unscrew the pump and sort the parts separately – the bottle is made of PET and the pump of PP.
Frequently asked questions
Parameters
Plastic bottle, clear round, type B, 24/410, 300 ml, without cap
Transparent Plastic Pump, 24/410, FBOG 200 mm
Product documentation
- DrawingTechnical drawing
- PDF ↓
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.

























































