PLASTIC BOTTLES
Clear plastic bottle, clear pump, 500 ml
Pack size100 ml150 ml200 ml250 ml500 ml
Clear plastic bottle with pump, 500 ml is a set for liquid and medium-thick cosmetic products that are dispensed by pressing the pump: liquid soaps, shower gels, shampoos, conditioners, body lotions and facial cleansing… full description
Lowest price in the last 30 days: €0.89
Total for 1 pcs: €1.28
Quantities add up across all combinations of this bottle.
Product description
Clear plastic bottle with pump, 500 ml is a set for liquid and medium-thick cosmetic products that are dispensed by pressing the pump: liquid soaps, shower gels, shampoos, conditioners, body lotions and facial cleansing gels. The PET bottle is lightweight, and the clear walls let you see the quantity and colour of the contents. The PP pump with a 24/410 neck finish dispenses approximately 1.4 ml per press, which corresponds to a typical single dose of liquid soap or shower gel. Both components are declared as suitable for contact with cosmetic products. The set as a whole is intended for cosmetics and is not approved for contact with food.
What the set is suitable for
The 500 ml volume and pump dispensing suit mainly products that are used daily and in small doses:
- Liquid hand soap – for the sink in the bathroom or kitchen, dispensed with one hand without unscrewing a cap.
- Shower gels and shampoos – the clear bottle lets you see how much product is left, and the pump limits water access to the contents.
- Body and face lotions – thinner emulsions that the pump draws up without problems.
- Conditioners and cleansing gels – a larger pack for the home, a salon or as a supplement to smaller bottles.
Clear plastic does not protect the contents from light. Products with light-sensitive ingredients, for example with a high proportion of essential oils or unstabilised plant extracts, are better suited to dark glass or opaque packaging.
Nominal and total volume
The 500 ml figure is the nominal volume, that is, the quantity the bottle is designed to hold when filled normally. The total brim-full volume is somewhat larger, because the neck and the upper part of the bottle form a reserve for the pump dip tube and for the expansion of the contents with temperature changes. Fill the bottle to the nominal volume, not up to the neck. If it were filled to the brim, the dip tube would displace the contents and the pump would not seat on the thread.
Before first use, insert the pump dip tube into the empty bottle and check that it does not bend against the bottom when tightened. If it is too long, shorten it with a diagonal cut so that its end does not stick to the bottom and block suction.
How to use the set
Before first filling, wash the bottle and the pump, disinfect them with isopropyl alcohol or ethanol and let them dry completely. Rinse the pump by pumping clean water through it several times and then alcohol, so that the inner part of the pump is clean as well. Fill the product once it has cooled to room temperature. The PET bottle is not designed for hot filling and must be protected from heat. After fitting, tighten the pump by hand, without force, and allow for the first few presses to fill the dip tube and the pump with the product.
With emulsions and gel formulations, dispensing depends on viscosity. The pump draws up thinner products without problems, while with thicker lotions the dose becomes smaller or the pump draws in air. Check the behaviour with your specific formulation before filling a whole batch. Thick ointments and products with granular particles, for example scrubs, do not belong in the pump, as they would clog the valve.
Concentrated essential oils, undiluted fragrance compositions and solvents may damage plastic over the long term. Do not store such raw materials in the set. For formulations with a higher proportion of essential oils, test the stability of the packaging and the tightness of the pump in advance.
Good to know
The set can be used repeatedly. Once the contents are used up, wash and disinfect the bottle and the pump in the same way as before first use, and when changing the product let the packaging dry completely.
The bottle and the pump are made of different plastics, so separate them for disposal. The PET bottle belongs with plastics marked 1, the PP pump is marked 5.
The declaration of conformity and the certificate of suitability for contact with cosmetics are available for each component of the set. If you want a different closure for the bottle, closures with the same 24/410 neck finish are suitable, and you will find ready-made combinations in the Handymade range. With your own combination, check the tightness, dispensing and behaviour of the packaging with your specific formulation.
Frequently asked questions
Parameters
Plastic bottle, clear 24/410, 500 ml
- Product colour
- Clear
- Country of origin
- European Union
- Nominal capacity
- 500
- Diameter
- 67 mm
- Thread type
- 24/410
- Height
- 177 mm
Transparent Plastic Pump, 24/410, FBOG 200 mm
Product documentation
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.























































