PLASTIC BOTTLES
Rounded Clear Plastic Bottle, Type B, White Lotion Pump With Overcap, Glossy Gold, 300 ml
Pack size100 ml150 ml200 ml300 ml
A clear PET bottle with a volume of 300 ml and a white and gold pump with overcap makes a ready-to-use set for products that are dispensed by pressing: shower gels, shampoos, conditioners, body lotions or liquid hand… full description
Lowest price in the last 30 days: €1.59
Save €0.01 with this set
Total for 1 pcs: €1.59
Quantities add up across all combinations of this bottle.
Product description
A clear PET bottle with a volume of 300 ml and a white and gold pump with overcap makes a ready-to-use set for products that are dispensed by pressing: shower gels, shampoos, conditioners, body lotions or liquid hand soap. The clear plastic shows the colour of the product and how much of it is left in the bottle. The pump dispenses roughly the same amount with each press, and the overcap protects the pump head from dust and from being pressed accidentally during transport. The bottle is light, so it suits the bathroom, the shower and travel.
Both the bottle and the pump have a 24/410 neck finish, so they fit together without trial and error, and the dip tube of the pump reaches the bottom of the bottle. Both components are declared suitable for contact with cosmetic products. The set is not approved for contact with food and is intended for cosmetics.
What the set is suitable for
- Shower gels and shampoos – a volume of 300 ml lasts several weeks in the shower, and the pump can be operated with one hand, even with wet fingers.
- Body lotions and light creams – thinner emulsions pass through the dip tube without problems, and one dose corresponds to the amount needed for the hands or forearm.
- Liquid hand soap – at the sink, the set replaces disposable dispensers and can be refilled repeatedly.
- Massage and body oils – the pump measures out the oil without spilling. With a high proportion of essential oils, first check how PET behaves with your formulation.
Filling and dispensing
The nominal volume is the amount the bottle is designed for during normal filling. The brimful volume is larger, because space is left above the nominal level for the dip tube and the pump. Therefore fill only up to the nominal volume. If the bottle is overfilled, the dip tube pushes part of the contents out through the neck when the pump is screwed on, the bottle gets dirty and the seal is poorer.
One press dispenses approximately 0.2 ml, and the actual amount depends on the viscosity of the product. Liquid to medium-thick products dispense best: gels, shampoos, lotions, oils. A thick cream that you would scoop from a jar with your finger will not pass through the dip tube, or the pump will work irregularly. Very thin water-based solutions may in turn splash when pressed, and a fine mist sprayer is more suitable for those.
Before the first filling, wash the bottle and the pump, spray or wipe them with isopropyl alcohol or ethanol and let them dry completely. After filling, press the pump several times to prime it until the dip tube and the pump head fill with the product. Only then is the dose stable.
Good to know
Clear PET does not block light. Fill it with products containing vegetable oils, essential oils or sensitive active ingredients only if you will use them up within a few weeks, or store the bottle out of direct sunlight. Dark packaging is more suitable for formulations that are stored for a long time or are sensitive to light.
PET tolerates water-based solutions, emulsions, surfactant products and common vegetable oils well. For formulations with a high content of alcohol, solvents or concentrated essential oils, leave a sample in the bottle for several days and check whether the plastic turns cloudy, softens or becomes deformed. The same applies to the pump, whose parts are made of polypropylene and aluminium.
The set can be used repeatedly. Before each new filling, take the bottle and the pump apart, rinse them with warm water and a small amount of washing-up liquid, pump clean water through the pump several times and let everything dry. Residues of the old product in the dip tube could otherwise contaminate the new filling. The bottle is made of PET and the pump of PP and aluminium, so separate them for recycling and sort them according to local rules.
Hot water and direct heat deform a PET bottle. Do not fill it with a hot emulsion and do not sterilise it by boiling. Let the product cool to room temperature before filling.
The bottle has a 24/410 neck finish. You can find other closures with the same type of thread, as well as ready-made bottle and closure combinations, in the Handymade range. If you make your own combination, check the seal and the dispensing with your specific formulation.
Frequently asked questions
Parameters
Plastic bottle, clear round, type B, 24/410, 300 ml, without cap
White Lotion Pump With Overcap, 24/410, Glossy Gold, 200 mm
- Country of origin
- European Union
- Diameter
- 27,5 mm
- Thread type
- 24/410
- Height
- 45 mm
- Tube length
- 220 mm
- Dose
- 0,2 ml
Product documentation
- DrawingTechnical drawing
- PDF ↓
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.
































































