PLASTIC BOTTLES
White Plastic Bottle, Transparent Plastic Pump, 100 ml
A white plastic bottle with a capacity of 100 ml and a clear pump with a 24/410 neck finish is ready-made packaging for cosmetics dispensed by pressing: body and face lotions, liquid soaps, lighter creams, shampoos or… full description
Lowest price in the last 30 days: €0.69
Total for 1 pcs: €1.07
Quantities add up across all combinations of this bottle.
Product description
A white plastic bottle with a capacity of 100 ml and a clear pump with a 24/410 neck finish is ready-made packaging for cosmetics dispensed by pressing: body and face lotions, liquid soaps, lighter creams, shampoos or cleansing gels in travel or sample sizes. The PET bottle is lightweight and shatter-resistant, and the white opaque material limits the amount of light reaching the contents. The pump releases approximately the same amount with each press, so the product is dispensed without opening the bottle and without unnecessary contact with your hands.
The set is declared suitable for contact with cosmetics. Only the bottle has a certificate for direct food contact; the pump does not, so the set as a whole is intended for cosmetics.
What the set is suitable for
- Body and face lotions – thinner emulsions pass smoothly through the dip tube and the pump valve, and one dose is enough for one use.
- Liquid soaps and cleansing gels – a pump by the sink or in the shower can be operated even with wet hands.
- Lighter creams and hair products – conditioners, styling lotions or hand creams with a softer consistency that the pump valve can still push through.
- Samples and travel size – the 100 ml volume suits testing a formulation with customers or a smaller batch of your own cosmetics.
Very thick creams, balms and products with scrub particles do not belong in this packaging. The pump either will not draw them up or it will clog. For a borderline consistency, fill one bottle and test whether the pump draws evenly.
Filling and volume
The nominal volume of 100 ml is the volume the bottle is designed for under normal filling. The total brimful volume is the physical volume up to the neck and you can find it in the parameters. The difference between the two values is a reserve for the dip tube and the pump valve and for expansion of the contents when the temperature changes. Fill the bottle up to the nominal volume, not to the brim. If the bottle is overfilled, the pump pushes part of the contents out through the neck when it is screwed on.
Let emulsions and gels cool before filling. PET is not designed for hot filling, and warm contents may deform the bottle wall.
Working with the pump
The pump dip tube is supplied longer than the height of the bottle so that it can also be used in taller packaging with the same neck. Before first use, trim it so that its end reaches just above the bottom of the bottle and does not bend against it. After screwing the pump on, prime it with several empty presses until the tube and chamber fill and the product starts to come out.
One press releases approximately 1.4 ml. Thicker products dispense somewhat less and more slowly. The clear pump body shows whether the chamber is filled and whether air is trapped in it.
Cut the tube straight with a sharp knife or scissors, not at an angle with a torn edge. A straight cut above the bottom of the bottle draws evenly and does not leave as much unused residue.
Good to know
- Preparation before first filling – wash the bottle and the pump, disinfect them with isopropyl alcohol or ethanol and let them dry completely. Also flush the inside of the pump with alcohol by pressing it several times.
- Essential oils and solvents – both PET and PP tolerate common cosmetic emulsions and oils, but aggressive chemicals damage the packaging. For formulations with a higher proportion of essential oils, alcohol or solvents, test how the packaging behaves with your specific formulation.
- Reuse – after thorough washing and drying, the bottle and the pump can be filled again. When cleaning, pump warm water through the pump so that residues of the previous product are released from the valve.
- Other closures – closures with the same neck type fit the bottle, and you can find ready-made combinations in the Handymade range. For your own combination, check the seal and the dispensing with your specific formulation.
- Recycling – the bottle is made of PET and the pump of PP, so separate them on disposal and put them in the plastics bin.
Frequently asked questions
Parameters
White plastic bottle, 24/410, without cap, 100 ml
Transparent Plastic Pump, 24/410, FBOG 200 mm
Product documentation
- DrawingTechnical drawing
- PDF ↓
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.

































































