PLASTIC BOTTLES
White Plastic Bottle, Black Lotion Pump With Glossy Silver Collar, 150 ml
Pack size100 ml150 ml200 ml250 ml300 ml
This white plastic bottle with a 150 ml volume and a black and silver pump is intended for cosmetics that are dispensed by pressing: body lotions, liquid soaps, shampoos, conditioners, massage oils or facial cleansing… full description
Lowest price in the last 30 days: €1.29
Total for 1 pcs: €1.29
Quantities add up across all combinations of this bottle.
Product description
This white plastic bottle with a 150 ml volume and a black and silver pump is intended for cosmetics that are dispensed by pressing: body lotions, liquid soaps, shampoos, conditioners, massage oils or facial cleansing gels. The white PET bottle lets less light through to the contents than clear packaging, is lightweight and, unlike glass, does not break if dropped in the bathroom or during transport. The pump with a 24/410 neck finish dispenses approximately 1 ml per press, so the product is taken out in measured doses and you do not need to put your fingers into the bottle. The set is declared suitable for contact with cosmetics.
What the set is suitable for
- Body lotions and light emulsions – liquid to medium-thick emulsions pass through the pump without effort, and one dose is enough to treat the hands or forearm.
- Liquid soaps and shampoos – at the sink or in the shower, the product is dispensed with one hand. This is why a pump is chosen instead of a cap for rinse-off products.
- Body and massage oils – the pump measures out a small amount of oil without tilting the bottle and without the contents spilling.
- Cleansing gels and micellar products – a measured dose keeps consumption under control, and the contents stay out of contact with the skin until use.
- Samples and small batches – the 150 ml volume is suitable for testing a formulation or for gift packs where a larger volume would go unused.
How the pump works
The pump consists of a press head, a threaded 24/410 closure and a dip tube that reaches the bottom of the bottle. The first presses after filling draw the product into the mechanism, and only then does the pump deliver a full dose. The tube is supplied longer than the height of the bottle. Before fitting, it should therefore be cut at an angle so that it ends just above the bottom. We recommend transporting filled bottles in a way that prevents the head from being pressed on the way, or transporting the set empty and filling it at the place of use.
The consistency of the filling determines how the pump performs. Thick creams and balms are drawn up with difficulty or not at all, and very thin liquids such as toners may drip after pressing. We recommend testing the behaviour of your specific formulation on one bottle before you fill the whole batch.
Nominal and total volume
The nominal volume of 150 ml is the amount the bottle is designed for during normal filling. The total volume up to the neck is larger. This difference provides a reserve for the tube and the body of the pump, which push part of the contents upwards once screwed on. The bottle should therefore be filled up to the nominal volume. If it is filled to the brim, the product is pushed out through the neck when the pump is fitted.
Good to know
- Preparation before first filling – we recommend washing the bottle and the pump, disinfecting them with isopropyl alcohol or ethanol and leaving them to dry completely. Residual water would dilute the first doses of the product and increases the risk of contamination in emulsions.
- Compatibility with the contents – the bottle should not be exposed to aggressive chemicals. For formulations with a higher proportion of essential oils, alcohol or solvents, we recommend checking the behaviour of the packaging over time, especially the tightness of the thread and the smooth operation of the pump.
- Food – the certificate for direct food contact applies to the bottle alone. The pump does not have one, so the set as a whole is intended for cosmetics.
- Reuse – once the contents are used up, the bottle is washed and the pump is cleaned by pumping through warm and then clean water. When changing the product, dry the mechanism so that residues of the previous filling do not mix with the new one.
- Recycling – the bottle is made of PET and belongs with plastics. The pump combines PP and aluminium, so separate it from the bottle before sorting.
- Other closures – the bottle has a 24/410 neck finish, and you will find closures with the same type of neck and other ready-made combinations in the Handymade range. If you are making your own combination, we recommend checking the tightness and dispensing with your specific formulation.
Protect the bottle from heat and aggressive chemicals. Fill emulsions and oils only after they have cooled to room temperature, not straight after hot emulsification.
Frequently asked questions
Parameters
White plastic bottle, 150 ml 24/410, without cap
Product documentation
- PPWRPackaging Declaration (PPWR)
- PDF ↓

































































