PLASTIC BOTTLES
White Plastic Bottle, Black Lotion Pump With Glossy Silver Collar, 100 ml
Pack size100 ml150 ml200 ml250 ml300 ml
White plastic bottle with black and silver pump, 100 ml is a ready-made set for liquid and semi-liquid cosmetic products that are dispensed by pressing: body lotions, lighter creams, liquid soaps, shampoos, conditioners… full description
Lowest price in the last 30 days: €1.07
Total for 1 pcs: €1.07
Quantities add up across all combinations of this bottle.
Product description
White plastic bottle with black and silver pump, 100 ml is a ready-made set for liquid and semi-liquid cosmetic products that are dispensed by pressing: body lotions, lighter creams, liquid soaps, shampoos, conditioners and cleansing gels. The bottle is made of white PET, which hides the contents and reduces light exposure. The black and silver pump dispenses approximately 1 ml per press, so the customer can take a small, precise dose without their hands touching the contents.
Both parts have a 24/410 neck finish, so they fit together without any further adaptation. The bottle and the pump are both declared suitable for contact with cosmetic products. The certificate for direct food contact applies to the bottle on its own; the set as a whole is intended for cosmetics.
What it is for
- Body lotions and light emulsions – the pump dispenses them evenly and the contents stay in the closed bottle, so they do not dry out at the edge as in an open jar.
- Liquid soaps, shampoos and shower gels – the 100 ml volume is enough as a travel pack or as a sample for trying out a formulation.
- Cleansing gels and facial lotions – you can take a dose with one hand, even at the sink when the other hand is wet.
- Hydrating toners and hair tonics – if they are meant to be dispensed onto the palm rather than sprayed.
Very thick creams, butters and products with solid particles (scrubs, products with seeds or flakes) are not suitable for a pump. The product struggles to pass through the tube and the valve becomes clogged. For such products, choose a jar or a bottle with a cap instead.
How the set works
The pump has a dip tube that is longer than the height of the bottle. Before the first filling, it is shortened with a straight cut so that its end reaches just to the bottom. Otherwise an unused remainder of the contents is left at the bottom, or the tube bends inside the bottle. After fitting, press the pump several times until the contents rise into the head.
Shorten the tube only after you have first placed the pump on the filled bottle, so that you measure the correct length. Make the cut at a right angle.
Nominal and total volume
The figure of 100 ml is the nominal volume, that is, the amount the bottle is designed for in normal filling. The total brim-full volume is greater, because the bottle continues up to the neck. The difference provides room for the tube and the body of the pump, which push part of the contents upwards once fitted, and for the expansion of the product when the temperature changes. Therefore, fill only up to the nominal volume, not to the brim. If overfilled, the contents leak through the thread when the pump is screwed on.
Good to know
Preparation before the first filling. Rinse the bottle, disinfect it if needed with isopropyl alcohol or ethanol and leave it to dry completely upside down. Rinse the pump by pressing it several times in clean water and then pumping it dry, so that any residues run out of the tube and valve. Assemble only when the parts are dry.
Material sensitivity. PET tolerates water-based and emulsion products well, but it should not be exposed to aggressive chemicals. For formulations with a higher proportion of essential oils, alcohol or solvents, check beforehand that the bottle material and the pump seal do not change shape, crack or leak.
Reuse. Both parts can be used again after thorough washing and drying. The pump is most sensitive to dried residues in the valve, so rinse it with warm water immediately after emptying.
Recycling. The bottle is made of PET and belongs with plastics. The pump combines plastic and aluminium, so separate it from the bottle before disposal.
Closures with the same neck type and other ready-made combinations of this bottle can be found in the Handymade range. If you make your own combination, check the tightness, the dispensing and the behaviour of the packaging with your specific formulation.
The pump is not certified for contact with food. For this reason, do not use the set for homemade oils, syrups or other food products, even though the bottle itself has such a certificate.
Frequently asked questions
Parameters
White plastic bottle, 24/410, without cap, 100 ml
Product documentation
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.




































































