ALUMINUM BOTTLES
Aluminium Bottle, Black Lotion Pump With Glossy Silver Collar, 50 ml
Pack size50 ml100 ml200 ml225 ml
This aluminium bottle , with a capacity of 50 ml and a black and silver pump , is designed for liquid and cream cosmetic products that are dispensed in small doses. full description
Lowest price in the last 30 days: €2.50
Save €0.04 with this set
Total for 1 pcs: €2.50
Quantities add up across all combinations of this bottle.
Product description
This aluminium bottle, with a capacity of 50 ml and a black and silver pump, is designed for liquid and cream cosmetic products that are dispensed in small doses. Aluminium is lightweight, does not break when dropped and does not let light through, so the contents are protected from sunlight, even when travelling. The pump with a dip tube dispenses the contents without opening the bottle. The product is not contaminated by fingers, and each press releases the same amount. The set is declared suitable for contact with cosmetics.
What it is suitable for
The 50 ml size is easy to carry in a bag or on trips, or can serve as a tester and sample of a larger product. The pump handles liquid and medium-thick textures:
- Body and face lotions – light O/W emulsions are drawn up without problems and dispensed cleanly.
- Hand creams with a thinner consistency – a small pack for your desk or handbag.
- Face and hair serums – dispensing in individual doses without opening the bottle.
- Oil serums and massage oils – opaque aluminium protects oils and light-sensitive active ingredients.
- Liquid soaps and cleansing gels in a travel size – a pump is more convenient at the sink than a cap.
Thick creams, body butters and products with high viscosity will not be drawn up by the pump, or it will dispense them unevenly. For such formulations, choose a jar or packaging with a different closure instead.
How the pump works
The pump screws onto the neck of the bottle and the dip tube reaches the bottom, from where it draws up the contents. One press releases approximately 1 ml, which for a 50 ml bottle means approximately 50 doses. Before first use, prime the pump by pressing it several times until the tube fills and the product starts to flow out. The black and silver head matches the silver body of the bottle, so the packaging looks uniform.
The pump dip tube is longer than the height of this bottle. Before fitting it, shorten it with a straight cut using a sharp knife so that it ends just above the bottom and can draw up the remaining contents. A tube that is too long will bend inside the bottle and dispensing will stop working.
Volume and filling
The nominal volume is the amount the packaging is designed for under normal filling. The brimful volume is the physical volume of the bottle up to the neck, and you will find it in the parameters. The difference between them is a reserve for the dip tube and the pump body, which push the level upwards when screwed on. Fill the bottle up to the nominal volume, not to the brim. An overfilled bottle will overflow when the pump is fitted.
Fill only with a cooled product. Aluminium conducts heat well, so a hot emulsion would heat the whole bottle. A small funnel or syringe helps with filling, as the narrow neck is otherwise easily soiled.
Good to know
- Preparation before first filling – rinse the bottle, disinfect it with isopropyl alcohol or ethanol and let it dry completely. Pump clean water through the pump, then alcohol, and leave it to dry upside down.
- Reuse – once empty, the aluminium bottle can be washed and refilled. The pump is harder to clean, as residues of the old product in the tube and the mechanism are difficult to remove. If you change the recipe, it is better to replace it.
- Compatibility with the formulation – the pump contains plastic parts made of PP. Concentrated essential oils and solvents can damage plastics over time, so for formulations with a higher proportion of such ingredients, check how the packaging behaves in the finished product. Likewise, check how the aluminium bottle behaves with your specific formulation, especially for water-based products with a low or high pH.
- Closures – the bottle has a 24/410 neck finish. Other closures with the same neck type, as well as ready-made combinations of the bottle with a cap, sprayer or pump, are available in the Handymade range. If you make your own combination, check the tightness and dispensing with your specific product.
- Contact with cosmetics – both the bottle and the pump are declared suitable for contact with cosmetic products, and the declaration of conformity is available for each component. The set is not intended for food.
- Recycling – hand over the emptied and rinsed aluminium bottle for recycling as metal. The pump is a combination of plastic and aluminium, so separate it from the bottle when disposing of it.
The aluminium bottle is opaque, so the amount of remaining contents cannot be judged by eye. When selling, keep in mind that the customer will only find out the bottle is empty when the pump starts drawing in air.
Frequently asked questions
Parameters
Aluminium bottle, 24/410, 50 ml
Product documentation
- DrawingTechnical drawing
- PDF ↓
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.






















































