PLASTIC BOTTLES
Amber Plastic Bottle, Black Lotion Pump With Glossy Silver Collar, 150 ml
Pack size100 ml150 ml200 ml300 ml
This amber plastic bottle with a volume of 150 ml comes with a fitted pump with a 24/410 neck finish and is intended for filling liquid and cream cosmetic products that are dispensed in doses: body lotion, hand cream,… full description
Lowest price in the last 30 days: €1.40
Total for 1 pcs: €1.40
Quantities add up across all combinations of this bottle.
Product description
This amber plastic bottle with a volume of 150 ml comes with a fitted pump with a 24/410 neck finish and is intended for filling liquid and cream cosmetic products that are dispensed in doses: body lotion, hand cream, liquid soap, shampoo, conditioner or cleansing milk. The bottle is made of lightweight PET plastic. The amber colour reduces the amount of light reaching the contents, which is useful for products containing vegetable oils, extracts or active ingredients that are sensitive to light. The black and silver pump releases a measured dose with every press, the contents do not spill and fingers do not get into the bottle during use.
The set is declared as suitable for contact with cosmetic products, and the declaration of conformity for both the bottle and the pump is available with the product. Neither the bottle nor the pump is certified for contact with food, so the set is intended exclusively for cosmetics.
What it is suitable for
- Emulsions and lotions – body lotion, lighter creams and facial emulsions, where measured dispensing keeps the contents clean throughout the entire period of use.
- Rinse-off products – liquid soap, shower gel, shampoo or conditioner with a liquid to medium-thick consistency. The 150 ml volume corresponds to a travel size, or to a trial size before you fill the recipe into a larger pack.
- Cleansing and make-up removal products – micellar water, cleansing milk or cleansing gel.
- Oil-based products – massage or body oil. For blends with a higher proportion of essential oils, we recommend first checking how the plastic behaves in contact with the specific formulation.
How the pump works
One full press releases approximately 1 ml of the contents. The actual amount depends on the thickness of the product and on whether the pump has been fully primed. The first few presses after filling draw the contents into the tube. The pump works without problems with liquid and medium-thick textures. Thick creams and butters are drawn up through the tube poorly, and the pump sticks or draws in air. A jar or a bottle with a different type of closure is more suitable for such products.
The pump tube is 180 mm long, so it is longer than the bottle and needs to be adjusted before fitting. Shorten it with a diagonal cut so that it ends just above the bottom. This way the pump draws up almost all of the contents and the tube does not bend when the pump is screwed on.
Cut the tube with sharp scissors only after you have held the pump against the bottle for a trial fit and measured the required length. A tube that is too short leaves a residue of product at the bottom that can no longer be pumped out.
Volume and filling
The nominal volume of 150 ml is the amount the bottle is designed for under normal filling. The total brimful volume given in the parameters is the physical volume up to the neck. The difference between them is a reserve for the tube and the body of the pump, which take up part of the space once screwed on. The bottle is therefore filled to the nominal volume, not to the brim. If it were filled up to the neck, part of the contents would be pushed out when the pump is fitted and the thread would get dirty.
Good to know
- Preparation before first filling – wash the bottle with warm water and a cleaning product, disinfect it with isopropyl alcohol or ethanol and leave it to dry completely. Pump clean water through the pump and then air, until it stops dripping.
- Fill once cooled – pour emulsions and liquid soaps into the PET bottle only after they have cooled completely. Hot contents may deform the plastic, and the finished product in the bottle should be protected from heat during storage as well.
- Aggressive ingredients – concentrated essential oils, solvents and products with a high proportion of alcohol may gradually damage the plastic and the pump seal. For such recipes, we recommend first leaving the filled set to stand and monitoring leak-tightness, cloudiness and pump operation.
- Reuse – after thorough washing and disinfection, the bottle can be filled again. When changing the fragrance or the type of product, a new pump is a safer choice.
- Other closures – the bottle has a 24/410 neck finish, so other closures with the same neck finish from the Handymade range also fit it. For your own combination, we recommend checking leak-tightness and dispensing with the specific formulation.
- Recycling – the bottle is made of PET, the pump of polypropylene with an aluminium element. Before disposal, unscrew the pump and sort it separately from the bottle.
The set is not intended for food. Do not fill it with homemade oils, syrups or herbal infusions, as neither the bottle nor the pump has a certificate for contact with food.
Frequently asked questions
Parameters
Brown plastic bottle, 24/410, 150 ml
- Product colour
- Brown
- Country of origin
- European Union
- Nominal capacity
- 150
- Brimful capacity
- 170 ml
- Diameter
- 49 mm
- Thread type
- 24/410
- Height
- 118 mm
Product documentation
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.





































































