GLASS BOTTLES 30 ml
Blue Glass Bottle, Black Lotion Pump with Black Overcap, 30 ml
Pack size10 ml15 ml30 ml50 ml100 ml
A glass bottle with a lotion pump is a set for creams, facial emulsions and thicker serums that you want to dispense in small amounts without scooping them out of a jar with your finger. full description
Lowest price in the last 30 days: €0.87
Total for 1 pcs: €0.87
Quantities add up across all combinations of this bottle.
Product description
A glass bottle with a lotion pump is a set for creams, facial emulsions and thicker serums that you want to dispense in small amounts without scooping them out of a jar with your finger. The blue medicine bottle from the European Handymade range screws onto a pump designed for thicker textures, so it also suits eye creams or cream masks. The nominal volume of 30 ml holds enough facial cream for several weeks of use, which is why the set is often chosen for trial batches and small runs.
Both the bottle and the pump are declared suitable for contact with cosmetics; you will find the declaration of conformity with the product. The set is intended for cosmetic products and is not approved for food. Glass does not change the scent or colour of the contents, which you will appreciate with fragranced creams and emulsions with essential oils. The black top of the pump gives the packaging a uniform look.
What the set is suitable for
- Facial and eye creams – the pump dispenses a small amount and the rest of the product does not touch your hands, so the contents stay clean for longer.
- Thicker serums and both O/W and W/O emulsions – cream textures pass through the pump evenly.
- Creams with light-sensitive ingredients – blue glass blocks part of the light, so it protects the contents better than clear glass.
- Samples and test batches – the small volume allows you to check the stability of a formulation before filling larger packaging.
Filling and dispensing
The nominal volume is the amount the bottle is designed to hold when filled normally. The brimful volume given in the parameters is the physical volume up to the neck. The difference between them provides a reserve for the dip tube of the pump and for the expansion of the contents with temperature changes. Fill to the nominal volume, not to the brim, otherwise the cream will overflow through the neck when the pump is screwed on and make the thread sticky.
One press dispenses approximately 0.14 ml of cream. After filling and screwing on the pump, several presses without product are needed until the pump draws the product up the dip tube. The dip tube of the pump is longer than the bottle itself, so shorten it with a sharp knife before first use so that it ends just above the bottom. The pump then draws out even the last of the contents and the tube does not bend.
Fill the cream into the bottle at the stage when it has already cooled after emulsification but is still pourable. A thick mass poured cold creates air bubbles, and the pump then dispenses unevenly.
Good to know
Before first filling, wash the bottle, disinfect it with isopropyl alcohol or ethanol and leave it to dry completely. It is enough to rinse the pump with warm water with a drop of surfactant and pump it empty until clean water runs out. Clean it the same way for repeated use, as remnants of old cream in the dip tube could spoil a new batch.
With every press, the pump with a dip tube draws air into the bottle, so the contents are not sealed off from the surroundings as in an airless system. For water-based formulations, the same need for preservation applies as for a cream in a jar. The plastic parts of the pump are made of PP. For formulations with a high proportion of essential oils or with solvents, we recommend testing the behaviour of the pump on one sample over several weeks.
Very thin oils, toners and water-based serums are not suitable for a lotion pump. The pump is designed for thicker textures, and liquid contents may leak from the neck or be dispensed in irregular amounts. A bottle with a dropper or sprayer is better suited to such products.
You will find closures with the same neck type as stated in the parameters, and other ready-made combinations, in the Handymade range. If you make your own combination, we recommend checking the tightness, dispensing and behaviour of the packaging with your specific formulation. After it is empty, the glass bottle belongs in glass waste and the pump in plastics; separate them before sorting.
Glass tolerates heat, but not a sudden change of temperature. Do not pour a hot emulsion into a cold bottle, and do not put a filled bottle in the fridge straight after filling. Let it cool to room temperature first.
Frequently asked questions
Parameters
Glass bottle, vial, blue, 18 mm, 30 ml
Product documentation
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.
























































































