GLASS BOTTLES up to 10 ml
White Glass Bottle, Glossy Gold Black Pump with Smoky Overcap, 10 ml
Pack size10 ml15 ml30 ml100 ml
This white glass medicine bottle with a volume of 10 ml and a glossy black and gold pump is intended for small packs of facial serums, oils and liquid preparations that are applied in small doses. full description
Lowest price in the last 30 days: €1.79
Total for 1 pcs: €1.79
Quantities add up across all combinations of this bottle.
Product description
This white glass medicine bottle with a volume of 10 ml and a glossy black and gold pump is intended for small packs of facial serums, oils and liquid preparations that are applied in small doses. With every press the pump dispenses a measured amount, so the contents do not have to be poured out, scooped or touched with a finger. The white glass hides the contents and limits the access of light, which you will appreciate with oil serums and active ingredients that are sensitive to light.
A volume of 10 ml suits small batches: customer samples, testing a new formulation, travel packs or concentrated serums that are used up drop by drop. The smoky overcap protects the pump head from dirt, and because you can see through it, it also shows that the bottle is closed.
What the set is suitable for
- Facial serums – water-based and oil-based serums applied in a small amount to the face, neck and décolleté area.
- Oil elixirs – blends of vegetable oils with active ingredients, where protection from light and precise dispensing are valued.
- Liquid foundations and primers – thin to medium-thick preparations that the pump can draw up.
- Trial packs – small runs for testing a formulation or for handing out samples before producing a larger batch.
Thick creams and butters do not belong in this pack. The pump is intended for liquids; with a thick product it will jam or dispense an uneven dose. With medium-viscosity products, for example a light emulsion, first check that the pump draws it up and that no residue remains in the head after pressing.
Dispensing and filling
One press dispenses approximately 0.14 ml, which corresponds to a few drops. The figure is indicative and varies with the thickness of the contents: the pump dispenses thinner liquids in the full amount and thicker ones in a smaller amount.
Before first use, prime the pump by pressing it several times until the dip tube fills and the contents start to come out. The bottle is filled up to the nominal volume, that is 10 ml, not up to the brim of the neck.
The nominal volume is the amount the packaging is designed for under normal filling. The brimful volume given in the parameters is the physical volume up to the neck. The difference provides room for the dip tube with the pump head and for the expansion of the contents when the temperature changes. If you fill the bottle to the brim, part of the contents will overflow when the pump is screwed on.
Good to know
The glass bottle has a declaration of suitability for use with cosmetic products. No such declaration is available for the pump, so check its behaviour with your specific formulation, especially with a higher proportion of essential oils, alcohol or solvents. The set is not intended for contact with food.
Before the first filling, wash the bottle, disinfect it with isopropyl alcohol or ethanol and let it dry completely, so that no residual moisture gets into the contents. You disinfect the pump by pumping alcohol through the dip tube and the head, then let it dry with the head uncovered.
The dip tube of the pump is longer than the bottle. Before first assembly, shorten it with a sharp knife using a diagonal cut so that it reaches the bottom without resting on it and without being bent. The pump will then draw up even the last drops.
After thorough washing and disinfection, the bottle can be reused. The pump is harder to clean after oil-based contents, and residues of the old contents in the dip tube can spoil the new contents, so when you change the formulation it is better to replace it with a new one. You will find closures with the same neck finish and ready-made combinations in the Handymade range. If you make your own combination, check the tightness and the behaviour of the closure with your specific formulation.
Glass belongs in glass recycling. The pump combines polypropylene and aluminium, so before disposal separate it from the bottle and dispose of it according to the materials it is made of.
Frequently asked questions
Parameters
Glass bottle, vial, white, 10 ml
Product documentation
- PPWRPackaging Declaration (PPWR)
- PDF ↓
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.






















































































