GLASS BOTTLES up to 10 ml
White Glass Bottle, Black Lotion Pump with Black Overcap, 10 ml
Pack size10 ml15 ml30 ml100 ml
A white glass medicine bottle with a volume of 10 ml and a black lotion pump is used for filling creams, eye creams and thicker serums in a small pack. full description
Lowest price in the last 30 days: €1.38
Save €0.03 with this set
Total for 1 pcs: €1.38
Quantities add up across all combinations of this bottle.
Product description
A white glass medicine bottle with a volume of 10 ml and a black lotion pump is used for filling creams, eye creams and thicker serums in a small pack. Each press of the pump releases approximately the same small amount, so the contents are not scooped out with a finger and no dirt from the hands gets into the bottle. White glass also shields the contents from light.
The set is supplied as a bottle and a pump together. Both parts are declared suitable for contact with cosmetic products, and the whole set is intended for cosmetic preparations. The same pack is suitable for your own production, for customer samples and for small batches where you need several pieces with a uniform look.
What the set is suitable for
- Eye creams – they are dispensed in small amounts, the contents stay free of finger contact and the volume matches usual consumption.
- Cream serums and light creams – the consistency the lotion pump is designed for. The pump draws them up without problems and one dose can be spread over a smaller area.
- Concentrated preparations – formulations with a higher proportion of active ingredients, where little product is used at a time and repeatable dispensing matters.
- Samples and travel packs – glass with a pump looks like a finished product even at a small volume.
How the pump works
The lotion pump is a plastic pump with a tube that draws the contents from the bottom of the medicine bottle. It works best with cream consistencies and body lotions. Thin water-based toners are dispensed poorly and may drip from the opening, and thick balms and butters are not drawn up by the pump. After fitting, press the pump several times without product until the tube and head fill and the product starts to come out.
The pump tube is longer than the height of the medicine bottle and is meant to be trimmed. Cut it so that the end reaches just above the bottom, and at a slight angle so that it does not stick to the glass when pressed. The pump can no longer draw up the small remainder at the bottom, and with thicker creams this remainder is larger.
Before cutting the tube, fit the pump onto an empty medicine bottle and mark where the tube reaches the bottom. A cut that is too short cannot be corrected, and a tube that is too long bends in such a low bottle and the pump stops drawing up product.
Nominal and brimful volume
Nominal volume is the amount the packaging is designed for in normal filling. Brimful volume, given in the parameters, is the physical volume up to the neck. The difference between them is a reserve for the pump with its tube, which takes up part of the inner space once screwed on, and for the expansion of the contents with temperature changes. Fill to the nominal volume, not to the brim. If overfilled, the cream is pushed out through the thread when the pump is fitted and the pump floods on the first press.
What to know before filling
- Preparation before first filling – wash the medicine bottle, disinfect it with isopropyl alcohol or ethanol and let it dry completely. Rinse the pump and let it dry as well, because water in the tube would get into the product.
- Filling temperature – let the emulsion cool before filling. Hot contents stress the glass through a sudden change of temperature, and moisture condenses under the fitted pump and drips back into the cream.
- Preservation – the pump limits contact of the contents with fingers, but the system is not airless. A water-based emulsion needs a preservative system just as in a jar.
- Reuse – the glass can be washed and used repeatedly. The pump cannot be fully taken apart, and residues of the previous product in the tube and head can only be removed by rinsing. We recommend a new pump for a new product.
- Closures – other closures with the same neck type and ready-made combinations can be found in the Handymade range. If you make your own combination, we recommend checking the tightness and dispensing with your specific formulation.
- Recycling – before disposal, separate the glass from the plastic pump, as each material belongs in a different sorted waste stream.
Do not fill the lotion pump with creams containing coarser particles, for example scrub granules or undissolved pigments. The particles get caught in the pump valve and dispensing stops.
Frequently asked questions
Parameters
Glass bottle, vial, white, 10 ml
Black plastic cream pump 18 mm, black top
Product documentation
- PPWRPackaging Declaration (PPWR)
- PDF ↓
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.






















































































