+421 950 333 113info@handymade.store−10 %Shop now

GLASS BOTTLES 50 ml

Clear Frosted Glass Bottle, Lotion Pump, 50 ml

Pack size15 ml30 ml50 ml

The set of a 50 ml glass bottle with a black lotion pump is ready for filling with face creams, lotions and emulsion serums. full description

AvailabilityPre-order
Product codeO18SN050-OVD18PC2
€1.04incl. VAT

Lowest price in the last 30 days: €1.04

Expected back in stock: 25 Nov.This variant is currently out of stock — your order will be a pre-order and delivery may take longer.
Volume pricing
1–251 pcs€1.04Your price
252–1007 pcs€0.95−8 % · 1× plato
1008–5039 pcs€0.88−15 % · 4× plato
from 5040 pcs€0.78−25 % · 20× plato

Total for 1 pcs: €1.04

Quantities add up across all combinations of this bottle.

Product description

The set of a 50 ml glass bottle with a black lotion pump is ready for filling with face creams, lotions and emulsion serums. You do not scoop the cream out with your fingers and you do not open the bottle during use, as the pump dispenses a small measured dose with every press. With emulsions, this reduces contact of the contents with air as well as the risk of contamination. The matte glass hides the contents, so you can see only their outline.

The bottle and the pump are each separately declared as suitable for contact with cosmetic products, and the set as a whole is intended for cosmetics. You will find the declaration of conformity with the product.


How the set works

The lotion pump screws directly onto the neck of the bottle. It has an 18/415 neck finish and fits a bottle with an 18/410 neck finish, so the set fits together without any modifications. The cream is drawn up through a tube that reaches the bottom. One press dispenses approximately 0.12 ml, so press several times for a larger dose.

The pump needs to be primed before first use. Pressing it several times fills the tube and the head with cream, and only then does a full dose come out. With thicker emulsions, this takes a few more presses.

The dip tube is longer than the height of the bottle. Before the first filling, shorten it with a sharp knife or scissors so that it ends just above the bottom. A tube that is too long bends and the pump draws poorly.


What the set is suitable for

The lotion pump needs contents of medium thickness that can be pushed out when pressed and that the tube can draw up again.

  • Face and day creams – O/W emulsions with a creamy consistency that would otherwise be scooped out of a jar.
  • Face and body lotions – thinner emulsions, where the pump dispenses cleanly and without leaking.
  • Emulsion serums and light gel creams – the 50 ml volume corresponds to the usual pack size of serums and eye creams.
  • Hand creams – for a desk or bedside table, where the cream is used often.

The set is not suitable for thick butters, balms with a high wax content and scrubs with solid particles. The pump cannot draw up thick products, and particles clog the head. Very thin water-based products, for example toners, are dispensed by the pump, but the contents may drip from the head. We recommend testing how it behaves with your specific formulation on a small sample.


Nominal and total volume

The bottle is designed for a nominal volume of 50 ml, that is, the amount you work with in normal filling. The total brimful volume given in the parameters is the physical volume of the glass up to the neck and is higher. The difference is a reserve for the tube and the body of the pump, which take up part of the space once screwed on, and for the expansion of the contents when the temperature changes.

Fill to the nominal volume, not to the brim. If you fill to the neck, the cream overflows through the thread when the pump is screwed on and the set does not seal.


Good to know

Before the first filling, wash the bottle in warm water with a cleaning product, rinse it, disinfect it with isopropyl alcohol or ethanol and leave it to dry completely. It is enough to rinse the pump with clean water and leave it to dry with the tube pointing down. Leave alcohol on the plastic parts only briefly and then let it evaporate.

Glass does not tolerate sudden changes in temperature well. Leave the emulsion to cool to room temperature before filling and do not pour a hot mixture into a cold bottle. The pump is made of polypropylene (PP). For formulations with a high proportion of essential oils or solvents, we recommend testing the behaviour of the plastic parts beforehand.

Reusing the glass bottle is not a problem: just clean it before a new filling in the same way as before the first one. The pump can be used again if you rinse the tube and the head thoroughly with warm water and dry them. Residues of the old cream inside would otherwise mix with the new contents, so when you change the formulation it is more reliable to replace the pump with a new one.

Other closures can also be used on the bottle according to the neck type given in the parameters, and you will find ready-made bottle and closure combinations in the Handymade range. If you make your own combination, check the seal and the dispensing with your specific formulation.

For disposal, unscrew the pump from the bottle. The glass goes into glass recycling and the pump into plastics.


Frequently asked questions

Is the 50 ml glass bottle with a lotion pump suitable for thick creams and butters?
It is suitable for creams of medium thickness, but not for thick butters and balms. The lotion pump draws up the contents through a tube and needs a product that can be pushed out when pressed and that flows back to the tube. Body butters, balms with wax and scrubs with particles are not drawn up by the pump, or they clog its head. For a borderline consistency, we recommend testing on a small sample.
Does a lotion pump with an 18/415 neck finish fit a bottle with an 18/410 neck finish?
Yes, a lotion pump with an 18/415 neck finish fits a glass bottle with an 18/410 neck finish, and the set fits together without any modifications. The pump screws directly onto the neck and holds tightly. Before first use, shorten the dip tube so that it ends just above the bottom of the bottle.
How much cream fits in the 50 ml glass bottle with a pump?
The bottle is filled to the nominal volume of 50 ml, not to the brim. The total volume of the glass up to the neck is higher, and this difference is a reserve for the tube and the body of the pump and for the expansion of the contents when the temperature changes. If you fill to the neck, the cream overflows through the thread when the pump is screwed on and the set does not seal.
Why does the lotion pump not dispense on the first press?
The lotion pump has to be primed first, and during the first presses it draws cream into the tube and the head. Once primed, a full dose of approximately 0.12 ml comes out with every press. With thicker creams, this takes a little longer. If the pump does not draw even after several presses, check whether the tube is too long and bent.
Does the matte glass of the bottle protect the contents from light?
The matte glass only visually hides the contents, and you can see them in outline. It is neither dark glass nor opaque packaging. For this reason, store a finished product with sensitive ingredients away from direct sunlight, even in this bottle.
Can the glass bottle with a lotion pump be reused?
Yes, the glass bottle can be reused after thorough washing, disinfection with ethanol or isopropyl alcohol and complete drying. The lotion pump can be used again if you rinse the tube and the head with warm water and dry them. When you change the formulation, or if there are residues of the old cream in the pump, it is more reliable to use a new pump.

Parameters

Glass bottle, frosted clear, 18 mm, 50 ml

Product colour
Frosted
Country of origin
India
Nominal capacity
50
Brimful capacity
57 ml
Diameter
37,8 mm
Thread type
18/410
Height
92,3 mm
Product material
Glass

Plastic cream dispenser 18 mm, black

Product colour
BlackClear
Country of origin
China
Diameter
22,3 mm
Thread type
18/415
Height
40,1 mm
Product material
PPPlastic
Tube length
115 mm
Dose
0,12 ml

Product documentation

PPWRPackaging Declaration (PPWR)
Glass bottle, frosted clear, 18 mm, 50 ml · O18SN050PDF ↓
Plastic cream dispenser 18 mm, black · OVD18PC2PDF ↓
PDSProduct Data Sheet
Glass bottle, frosted clear, 18 mm, 50 ml · O18SN050PDF ↓
Plastic cream dispenser 18 mm, black · OVD18PC2PDF ↓
DrawingTechnical drawing
Glass bottle, frosted clear, 18 mm, 50 ml · O18SN050PDF ↓
Plastic cream dispenser 18 mm, black · OVD18PC2PDF ↓
Download all (ZIP)

6 PDF files in one archive

REVIEWS

Verified by customers.

No reviews yet.

Only customers with a delivered order can write reviews.