PLASTIC BOTTLES
Plastic bottle, vial, white, black and gold glossy pump, transparent cap, 50 ml
The plastic pharmaceutical bottle, white, with a glossy black and gold pump and clear overcap, 50 ml, is used for packaging liquid and creamy cosmetic products that are dispensed by pressing. full description
Lowest price in the last 30 days: €1.26
Total for 1 pcs: €1.26
Quantities add up across all combinations of this bottle.
Product description
The plastic pharmaceutical bottle, white, with a glossy black and gold pump and clear overcap, 50 ml, is used for packaging liquid and creamy cosmetic products that are dispensed by pressing. The white bottle is made of PET, lightweight and unbreakable if dropped, which you will appreciate for bathroom products or for travel. The nominal volume of 50 ml suits a serum, a fluid or a small pack of body lotion.
The pump with a glossy black and gold head and a clear overcap screws onto the thread of the bottle and draws the contents up through a dip tube from the bottom. The clear overcap covers the pump head against dust and accidental pressing, while leaving the look of the closure visible. The set is declared suitable for contact with cosmetic products, and a declaration of conformity has been issued for both components.
What it is suitable for
A pump with a small dose per press is intended for contents that flow freely or have the consistency of a light cream. This set is therefore filled mainly with:
- Facial serums and fluids – the small dose per press corresponds to the amount usually applied to the face, and the contents do not need to be poured out through the neck.
- Light O/W emulsions – facial and body lotions, light day creams and hand creams that the pump can draw up.
- Oil serums and oil blends – the pump copes with oils of common viscosity. For very thick oils, we recommend checking that the pump draws them up smoothly.
- Liquid soap and gel in a small pack – as a sample or travel pack, where 50 ml is enough.
Thicker creams, butters and balms are difficult or impossible to dispense through a pump. A jar or a bottle with a cap is more suitable for such products. For watery toners that you want to spray, use a fine mist sprayer.
Filling and dispensing
The packaging is filled up to the nominal volume, that is, the volume it is intended for in normal filling. The total volume to the brim is the physical volume of the bottle up to the neck and is slightly larger. The difference leaves a reserve for the dip tube and the pump body, which take up part of the inner space once screwed on, and for the expansion of the contents when the temperature changes. A bottle filled right up to the neck would overflow when the pump is fitted.
One press dispenses approximately 0.3 ml. This amount suits serums and concentrated preparations; with body lotion, the customer presses several times. Shorten the dip tube of the pump so that it reaches just to the bottom of the bottle and does not bend. The contents can then be used up almost completely. Before first use, the pump must be pressed several times until the tube fills.
Before first filling, wash the bottle and the pump, disinfect them with isopropyl alcohol or ethanol and leave them to dry completely. Residual water in the tube would get into the finished product.
Good to know
The bottle has a separate certificate for direct food contact; the pump does not have such a certificate. The set as a whole is therefore intended for cosmetics. If you need packaging for food use, choose a different closure for the bottle, one with the same neck type and its own certificate.
PET withstands common cosmetic raw materials, both water-based and oil-based. For contents with a high proportion of essential oils, alcohol or solvents, we recommend checking how the packaging behaves with the specific formulation, as aggressive chemicals can damage the plastic. The same applies to the pump, which combines PP and aluminium.
Both the bottle and the pump can be reused. The pump is rinsed by pumping warm water with washing-up liquid through it, then clean water, and finally pumping it empty so that it dries. When changing the contents, it is better to replace the pump, as traces of fragrance or colour are difficult to remove from the tube.
You will find closures with the same neck type and ready-made combinations of the bottle with other closures in the Handymade range. For your own combination, we recommend checking the tightness and dispensing with the specific formulation.
The clear overcap protects the pump head from being pressed, but for travel we recommend transporting the set upright or in a resealable bag.
For recycling, the PET bottle goes into plastic waste. Separate the pump before disposal, as it combines PP and aluminium.
Frequently asked questions
Parameters
Plastic bottle, boston round, white, 50 ml
- Product colour
- White
- Country of origin
- European Union
- Nominal capacity
- 50
- Diameter
- 34 mm
- Thread type
- G18x3
- Height
- 84 mm
Plastic pump dispenser, 18/415, glossy black and gold, clear top
- Country of origin
- European Union
- Diameter
- 25 mm
- Thread type
- 18/415
- Height
- 46 mm
- Tube length
- 100 mm
- Dose
- 0,3 ml
Product documentation
- DrawingTechnical drawing
- PDF ↓
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.





































































