GLASS BOTTLES 50 ml
Clear Frosted Glass Bottle, White Nasal Spray, 50 ml
A frosted glass bottle with a nasal sprayer is a ready-made set for thin, water-based liquids that are applied in small, measured doses. full description
Lowest price in the last 30 days: €1.52
Total for 1 pcs: €1.52
Quantities add up across all combinations of this bottle.
Product description
A frosted glass bottle with a nasal sprayer is a ready-made set for thin, water-based liquids that are applied in small, measured doses. The frosted glass diffuses light while still letting you see the liquid level, so you can tell how much is left in the bottle. The nasal sprayer with an 18/410 neck finish has a narrow, rounded applicator and delivers the same dose with every press. With thin solutions, there is no need to estimate the amount with a dropper or an ordinary sprayer.
The set is declared as suitable for contact with cosmetics. You will find the declarations of conformity for both the bottle and the sprayer on the product page. The set is not approved for contact with food.
Suitable uses
One dose has a volume of approximately 0.12 ml and leaves the applicator as a fine spray. The sprayer works best with liquids that have a viscosity close to water.
- Hydrosols in a small pack – lavender, rose or chamomile hydrosol for travel, for your handbag or as a trial sample.
- Thin toners and refreshing waters – water-based formulas without thickeners, where a small and even dose matters.
- Saline and mineral solutions – simple water-based solutions for refreshing the skin.
- Samples and test batches – a volume of 50 ml is enough to test a formula before filling a larger pack.
Thick formulations, emulsions and oils do not belong in this sprayer. The narrow nozzle becomes blocked or stops producing a spray. With water-alcohol mixtures, first test how the sprayer behaves on a small quantity.
Nominal and total volume
The bottle has a nominal volume of 50 ml. This is the amount the packaging is designed for in normal filling. The total volume to the brim is larger. The difference leaves room for the dip tube and the sprayer mechanism. Fill to the nominal volume, never to the neck. If the bottle is overfilled, some of the liquid is pushed out through the thread when the sprayer is screwed on.
Using the sprayer
Before first use, the pump must be primed. A few presses draw the liquid from the bottle into the tube and mechanism, and only then does the sprayer deliver a full dose.
If the tube hits the bottom and bends after the sprayer is fitted, shorten it with a sharp knife or scissors using a diagonal cut so that it ends just above the bottom of the bottle. The diagonal cut prevents the tube from sticking to the bottom, and the sprayer uses up almost the entire contents.
Good to know
- Preparation before filling – wash the bottle before first filling, disinfect it with isopropyl alcohol or ethanol and let it dry completely. Rinse the sprayer with clean water and pump several doses through it empty, so that no water remains in the mechanism.
- Reuse – the glass withstands repeated washing and disinfection. When changing the contents, rinse the sprayer thoroughly, as residues of the previous liquid stay in the tube and pump longer than it seems.
- Glass and heat – do not fill the bottle with hot liquids and avoid sudden changes in temperature. Let the contents cool to room temperature first.
- Compatibility with the formula – if you are combining your own packaging and contents, check the tightness, the quality of the spray and the behaviour of the sprayer with your specific formulation. The mechanism consists of several materials, including plastics, glass and steel, so a short test is worthwhile with every new formula.
- Preserving the contents – water-based liquids that are dispensed repeatedly need a suitable preservative system. The sprayer alone does not protect against microbial contamination.
- Recycling – the bottle belongs in glass recycling. The sprayer is made of several materials and is sorted according to local rules.
The sprayer is called a nasal sprayer because of the shape of its applicator. The set is declared for cosmetic products. The manufacturer of the finished product assesses, and is responsible for, its suitability for other product categories.
Frequently asked questions
Parameters
Glass bottle, frosted clear, 18 mm, 50 ml
Product documentation
Verified by customers.
No reviews yet.
Only customers with a delivered order can write reviews.






















































































